Oracle DB 설치 전 사전 시스템 작업 요약 정리


 

MOS에 좋은 자료를 소개 합니다. 오라클 DB 설치전에 서버 작업을 한눈에 OS 버전별로 정리 되어 있습니다.

 

 
 

Oracle Database (RDBMS) on Unix AIX,HP-UX,Linux,Mac OS X,Solaris,Tru64 Unix Operating Systems Installation and Configuration Requirements Quick Reference (8.0.5 to 11.2) (문서 ID 169706.1)

 

 



For 12c requirements refer to Note 1587357.1 


AIX 
HP-UX (PA-RISC and Itanium) 
Linux x86 
Linux x86-64 
Linux Itanium 
Linux on Power 
Linux on zSeries 
Mac OS X (PowerPC and x86-64) 
Oracle Solaris (SPARC and x86-64) 
Tru64 
Pre-Installation Scripts 
OPatch 
Related Documents 
OS Specific Commands 
Change History 
Note 43208.1 Certified Compilers 

Browse The Contents of Linux Brands ISOs


PURPOSE 
————–

This bulletin is produced to provide a central source for all the primary installation settings for the various mainstream unix platforms, e.g. IBM AIX, HP-UX, Oracle Solaris, Tru64, and Linux. 

Careful comparison of the Installation Guide and the applicable release note for an OS/Oracle version has been done to ensure that this bulletin provides the most complete source of data in hopes that it will save time for each researching analyst. 

Keeping the OS kernel current helps stabilize the system. Production systems should never run an out dated OS kernel version. As a best practice, Oracle recommends the OS kernel version be maintained to within 6 months of current. Please contact the OS vendor directly for more information, risk exposure, and patching recommendations. 

NOTE: Pre-compilers requirements are no longer addressed in this note, for a single source note 
that addresses Pre-compiler/Compiler requirements, please refer to: 
Note 43208.1 Certified Compilers

SCOPE & APPLICATION 
————————————-

This focus of this bulletin is on assisting the Oracle Unix installation community in resolving installation issues of the RDBMS. 
This bulletin places in one document all the pertinent information related to installations that has been extracted from three different documents (Installation Guides, Release Notes, and SRNs)

DISCLAIMER 
————

Whenever a contradiction arises between this document and My Oracle Support (MOS)-Certification, My Oracle Support (MOS)-Certification is the Certification authority. 
Users of this bulletin are obligated to provide real-time corrections/updates in the form of My Oracle Support (MOS) “Feedback” submissions to ensure the accuracy and up-to-date status of this bulletin.

PRE-INSTALLATION SCRIPTS 
————————————-

A decommissioned, non-supported script is still available to verify that the system has been configured correctly according to the 8.0.5 through 9.2 Installation Guides, please refer to the following My Oracle Support (MOS) Note for details: 
Note 189256.1 “UNIX: Script to Verify Installation Requirements for Oracle 8.0.5 to 9.2 versions of RDBMS”

The Remote Diagnostic Agent RDA (see Note 314422.1 for more info on RDA) has the capability to run a Pre-Installation check on several 10.1 and 10.2 Unix/Linux Platforms. 
Please refer to Note 250262.1 for specifics on how to run these Pre-Install scripts on your server.

OPatch FAQ 
————————————-

To apply one-off patches and Critical Patch Updates (CPUs) or Patch Set Update (PSU) on 9.2 and higer RDBMS versions you have to use the patching utility, OPatch. 
Oracle Support requests you always use the latest version before applying any patches to your server, to get the latest version, 
For 9.2 and 10.1 download 
Patch 6880880 
For 10.2, 11.1 & 11.2 download Patch 6880880 
Master Note For OPatch Note 293369.1 

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

AIX OS
(32- and 64-bit stands for Oracle not OS)

AIX 5L V5.3 TL 09 SP1 (“5300-09-01”) or higher, 64 bit kernel (Part Number E10854-01)

AIX 6.1 TL 02 SP1 (“6100-02-01”) or higher, 64-bit kernel

AIX 7.1 TL 00 SP1 (“7100-00-01”) or higher, 64-bit kernel

AIX 6.1L, AIX 5L version 5.3, TL 05, Service Pack 06 (Part Number B32076-03), AIX 6L version 6.1, TL 00, Service Pack 04 or later (Part Number B32076-03)

5.2 ML4 or higher, 5.3 ML2 or higher, 6.1

For AIX 6.1, only 10.2.0.3 or higher are certified

Customers running on 10.2.0.4 or higher and using CRS require AIX 5.3 TL5 (5300-05) or higher — seeNote:739371.1

5.2 ML1 or higher, 5.3

o 4.3.3 (64bit only) 
o 5.1, 5.2, 5.3 (5L)(64bit only)

4.3.3 (64bit)

o 4.3.2, 4.3.3 (32bit) 
o 5.1, 5.2 (5L) (32bit) [patch 2896876 is required if kernel is running in 64bit mode] 
o 4.3.2, 4.3.3 (64bit)

4.3.2, 4.3.3 (32 or 64bit)

o 4.2.1 , 4.3.0, 4.3.1, 4.3.2, 4.3.3 (32bit) 
o 4.3.2, 4.3.3 (64bit)

o 4.2.1, 4.3.2, 4.3.3 (32bit) 
o 4.3.2, 4.3.3 (64bit)

o 4.1.4, 4.1.5, 4.2.1, 4.3.2, 4.3.3 (32bit) 
o 4.3.2, 4.3.3 (64bit)

AIX Disk Space

6.40G Database 
1.55G Software

6.45G Database 
1.6G Software

1.2G Database 
3G Software 
1G Companion 
150M-1.9G Client

1.2G Database 
3G Software 
1G Companion 
150M-1.9G Client

4.5G

4.7G

1.58G

800Mb

800Mb

700Mb

700Mb

AIX RAM

Database: minimum 1GB, recommended 2GB

Grid Infrastructure for standalone server: minimum 1.5GB (plus another 1GB if installing Database too), recommended 4GB

1GB

1GB

512Mb 
256Mb(Client/Compan)

512Mb

512Mb

256Mb

128Mb

128Mb

64Mb or
128Mb / ConText

32Mb or
128Mb / ConText

AIX swap

Between 1GB and 2GB then 1.5 times RAM 
Between 2GB and 16 GB then match RAM 
More than 16 GB then 16GB RAM

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

1Gb or match RAM 
512Mb(Client/Compan)

1Gb or match RAM

400Mb

400Mb

400Mb

256Mb

2*RAM

2*RAM

AIX tmp

1GB

240Mb

400Mb

400Mb

400Mb

400Mb

400Mb

400Mb

50Mb

20Mb

20Mb

AIX JDK & JRE

IBM JDK 1.6.0.00 (64 BIT)

IBM JDK 1.5.0.06 (IA64 – mixed mode) is installed

IBM JDK 1.4.2 (32bit) is installed

IBM JDK 1.4.1.2 (32bit) is installed

JDK 1.3.1-build 20020316 & 1.1.8-Build 20020313

JDK 1.2.2.04 or JDK 1.2.2 & 1.1.8

JDK 1.1.8 / 1.2.2 & 1.1.8.3

1.1.8.3

?

n/a

n/a

AIX Patches/
Packages

versions in parens mean if OS is later than the listed version, the APAR is built into the later OS version and need not be applied. IMPORTANT: Review Note 390656.1 & apply AIX & Oracle Patch

AIX 5.3 required packages: 
bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.libperfstat 5.3.9.0 or later 
bos.perf.perfstat 
bos.perf.proctools 
rsct.basic.rte (For RAC configurations only) 
rsct.compat.clients.rte (For RAC configurations only) 
xlC.aix50.rte:10.1.0.0 or later 
xlC.rte.10.1.0.0 or later 
gpfs.base 3.2.1.8 or later (Only for RAC systems that will use GPFS cluster filesystems)

AIX 6.1 required packages: 
bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.libperfstat 6.1.2.1 or later 
bos.perf.perfstat 
bos.perf.proctools 
rsct.basic.rte (For RAC configurations only) 
rsct.compat.clients.rte (For RAC configurations only) 
xlC.aix61.rte:10.1.0.0 or later 
xlC.rte.10.1.0.0 or later 
gpfs.base 3.2.1.8 or later (Only for RAC systems that will use GPFS cluster filesystems)

AIX 7.1 required packages: 
bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.libperfstat 
bos.perf.perfstat 
bos.perf.proctools 
xlC.rte.11.1.0.2 or later 
gpfs.base 3.3.0.11 or later (Only for RAC systems that will use GPFS cluster filesystems)

Authorized Problem Analysis Reports (APARs) for AIX 5.3: 
IZ42940 
IZ49516 
IZ52331 
See Note:1379753.1 for other AIX 5.3 patches that may be required

APARs for AIX 6.1: 
IZ41855 
IZ51456 
IZ52319 
IZ97457 
IZ89165 
See Note:1264074.1 andNote:1379753.1 for other AIX 6.1 patches that may be required

APARs for AIX 7.1: 
IZ87216 
IZ87564 
IZ89165 
IZ97035 
See Note:1264074.1 andNote:1379753.1 for other AIX 7.1 patches that may be required

Refer to the 11.2 AIX Install Guide.Part Number E24332-01

6.1 / 5.3 ML5 required packages: 
bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.libperfstat 
bos.perf.perfstat 
bos.perf.proctools 
xlC.aix50.rte:8.0.0.7 or later (AIX 5.3) 
xlC.rte:8.0.0.7 or later (AIX 5.3) 
xlC.aix61.rte:9.0.0.1 or later (AIX 6.1) 
xlC.rte:9.0.0.1 or later (AIX 6.1) 
rsct.basic.rte (For RAC configurations only) 
rsct.compat.clients.rte (For RAC configurations only)

5.3 ML5 required patches: 
IY89080 
IY92037 
IY94343 
IZ01060 or efix for IZ01060 
IZ03260 or efix for IZ03260 (IZ03260 for ML6, IZ03475 for ML7) to address ORA-27061 
IY84780 
IY68989 

POWER7 Based Hardware 
Patch 9216848 (Note 1065579.1)

5.2 ML4 required patches: 
IY63133 
IY64978 
IY63366 
IY64691 
IY64737 
IY65001 
IY94343 Note 422031.1 LV Block Corruption

5.3 ML2 required patches: 
IY58143 
IY59386 
IY60930 
IY66513 
IY70159 
IY68989 
IY94343 Note 422031.1 LV Block Corruption 
Patch 5496862 is required (See Note 390656.1) if running on AIX 5.3 ML5 
IY84780 
IY68989

Important: Please see Note 282036.1for the latest patching requirements for 5.3 and 5.2

Required OS packages: 
bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.perfstat 
bos.perf.libperfstat 
bos.perf.proctools

6.1 specifics: 
Please download and run an updated version of rootpre.script before proceeding with the Oracle Database install. Internal bug 6613550. 6718715can be downloaded from My Oracle Support (MOS). 
Refer to Note 282036.1 for updates on any required patches for AIX 6.1 

Excessive Paging on IBM AIX POWER Systems Refer Note 1503072.1

5.2 required patches: 
IY43980 
IY44810 
IY45462 
IY45707 
IY46214 
IY46605 
IY48525 
IY51801 
IY59082 Refer to Note 285158.1 
IY94343 Note 422031.1 LV Block Corruption

5.3 required patches: Refer to Note 282036.1 
IY58143 
IY59386 
IY60930 
IY94343 Note 422031.1 LV Block Corruption 
Patch 5496862 is required (See Note 390656.1) if running on AIX 5.3 ML5. 
IY84780 
IY68989

Important: Please see Note 282036.1 for the latest patching requirements for 5.3 and 5.2

Required OS packages: 
bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.perfstat 
bos.perf.libperfstat 
bos.perf.proctools 
X11.motif.lib (Spatial only)

Async IO Hang, refer to Note 233659.1 for applicable patch for 4.3.3, 5.1, or 5.2

4.3.3 required patches/packages: 
IY30927(4.3.3.0.10) 
IY24568(4.3.3.0.09) 
IY25282(4.3.3.0.09) 
IY27614(4.3.3.0.09) 
IY30151(4.3.3.0.10) 
Maint Level 9 or higher (4.3.3.0.09)

bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.perfstat

5.1(5L) required patches/packages: 
IY26778(5100-01) 
IY28766(5100-01) 
IY28949(5100-01) 
IY29965(5100-02) 
IY30150(5100-02) 
IY59082 refer to Note 285158.1 
Maint Level 1 and IY22854

bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.perfstat 
bos.perf.libperfstat 
Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test (Note 293750.1)

Maint Level 7 or higher (4.3.3.0.07)

bos.adt.base 
bos.adt.lib 
bos.adt.libm 
bos.perf.perfstat 
X11.apps.rte 
X11.apps.xterm 
X11.base.rte 
X11.motif.lib 
X11.motif.mwm

IY01050 (4.3.3.0.03) 
IY07276 (4.3.3.0.02) 
IY05995 (4.3.3.01) 
IY02407 (4.3.2.02) 
IX89087 (4.3.2.0.02) 
IY03412 (4.3.2.0.02) 
IX85104 (4.3.2.0.01) 
IX87313 (4.3.2.0.01) 
IX87382 (4.3.2.0.01) 
IX89552 (4.3.2.0.01) 
IX81863 (4.3.1) 
IX72696 (4.3.0)

IY01050 (4.3.3.0.03) 
IY07276 (4.3.3.0.02) 
IY05995 (4.3.3.01)
IY07018 (4.3.3) 
IY02407 (4.3.2.02)
IX89087 (4.3.2.0.02) 
IY03412 (4.3.2.0.02) 
IX85104 (4.3.2.0.01) 
IX87313 (4.3.2.0.01) 
IX87382 (4.3.2.0.01) 
IX89552 (4.3.2.0.01) 
IX81863 (4.3.1) 
IX72696 (4.3.0)

4.2 related required APARs 
IX62429 (4.2.0) 
IX67174 (4.2.0) 
IX67978 (4.2.1) 
IX68932 (4.2.1) 
IX70737 (4.2.1) 
IX78933 (4.2.1.0.03) 
IX81957 (4.2.1.0.03) 
IX86229 (4.2.1.0.05)

4.3 related required APARs 
IX71948 (4.3.0) 
IX79690 (4.3.0) 
IX81863 (4.3.1)

bos.adt.base, bos.adt.libm 
must be installed

4.2 related required APARs
IX62429 (4.2.0) 
IX67174 (4.2.0) 
IX67978 (4.2.1) 
IX68932 (4.2.1) 
IX70737 (4.2.1) 
IX78933 (4.2.1.0.03) 
IX81957 (4.2.1.0.03) 
IX86229 (4.2.1.0.05) 
IX88178 (4.2.1.0.06)

4.3 related required APARs
IX71948 (4.3.0) 
IX79690 (4.3.0) 
IX81863 (4.3.1) 
IX87313 (4.3.2.0.01) 
IX87382 (4.3.2.0.01) 
IX89087 (4.3.2.0.02)

bos.adt.base, bos.adt.libm 
must be installed

4.1 related required APARs
IX54124 (4.1.4) 
IX55203 (4.1.5.0.01) 
IX62330 (4.1.5) 
IX58455 (4.1.4) 
IX61237 (4.1.4) 
IX67074 (4.1.5) 
IX61933 (4.1.5) 
IX70194 (4.1.5)

4.2 related required APARs
IX62429 (4.2.0) 
IX67174 (4.2.0) 
IX67978 (4.2.1) 
IX68932 (4.2.1) 
IX70737 (4.2.1) 
If running 4.2 then need bos.rte.libc version 4.2.0.5

4.3 related required APARs
IX71948 (4.3.0)

AIX Kernel Settings

set AIXTHREAD_SCOPE=S in the environment: 
export AIXTHREAD_SCOPE=S

NOTE: This is only necessary on AIX5L. A change was introduced in AIX 6.1 which means that the variable does not need to be set. See section 5.5 (page 217) of theIBM AIX Version 6.1 Differences Guide

From Section 2.6 of the 11.2 Install Guide for AIX

2.5 Verifying UDP and TCP Kernel Parameters 

Use NDD to ensure that the kernel TCP/IP ephemeral port range is broad enough to provide enough ephemeral ports for the anticipated server workload. Ensure that the lower range is set to at least 9000 or higher, to avoid Well Known ports, and to avoid ports in the Registered Ports range commonly used by Oracle and other server ports. Set the port range high enough to avoid reserved ports for any applications you may intend to use. If the lower value of the range you have is greater than 9000, and the range is large enough for your anticipated workload, then you can ignore OUI warnings regarding the ephemeral port range. 

Use the following command to check your current range for ephemeral ports: 

# /usr/sbin/no -a | fgrep ephemeral 
tcp_ephemeral_low = 32768 
tcp_ephemeral_high = 65535 
udp_ephemeral_low = 32768 
udp_ephemeral_high = 65535 

In the preceding example, the TCP and UDP ephemeral ports are set to the default range (32768-65536). 

If you expect your workload to require a high number of ephemeral ports, such as high node counts or heavy use of Parallel Query, then update the UDP and TCP ephemeral port range to a broader range. For example: 

# /usr/sbin/no -p -o tcp_ephemeral_low=9000 -o tcp_ephemeral_high=65500 
# /usr/sbin/no -p -o udp_ephemeral_low=9000 -o udp_ephemeral_high=65500

From Section 2.10 of the 11.2 Install Guide for AIX

2.8.2 Configure System Configuration Parameters 

Parameter Recommended Value 
maxuprocs 16384 
ncargs 128 

Also see Note:1307804.1

set AIXTHREAD_SCOPE=S in the environment: 
export AIXTHREAD_SCOPE=S

NOTE: This is only necessary on AIX5L. A change was introduced in AIX 6.1 which means that the variable does not need to be set. See section 5.5 (page 217) of the IBM AIX Version 6.1 Differences Guide

set AIXTHREAD_SCOPE=S in the environment: 
export AIXTHREAD_SCOPE=S

NOTE: This is only necessary on AIX5L. A change was introduced in AIX 6.1 which means that the variable does not need to be set. See section 5.5 (page 217) of the IBM AIX Version 6.1 Differences Guide

NOTE: It is not mandatory to set this variable if you are installing 10.2 client.

set AIXTHREAD_SCOPE=S in the environment: 
export AIXTHREAD_SCOPE=S

set AIXTHREAD_SCOPE=S in the environment: 
export AIXTHREAD_SCOPE=S

N/A

N/A

N/A

LINK_CNTRL = L_PTHREADS_D7 (if using 4.3)

LINK_CNTRL = L_PTHREADS_D7 (if using 4.3)

LINK_CNTRL = L_PTHREADS_D7 (if using 4.3)

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

HP OS
(32- and 64-bit stands for Oracle not OS)

HP-UX 11i V3 patch Bundle Sep/ 2008 (B.11.31.0809.326a) or higher (Part Number E10851-01)

11.23 and 11.31 (Itanium,PA-RISC)

11.11 (PA-RISC) (64bit) 
11.23 (PA-RISC) (64bit) 
11.23, 11.31 (PA-RISC / Itanium / IPF)

11.11 (PA-RISC) (64bit) 
11.23 (PA-RISC) (64bit) 
11.23, 11.31 (IA64 – Itanium) 
Note: for all Itanium systems using “Montecito” processors, refer tonote:400227.1 for special installation instructions

11.0 (64bit) 
11.11 (64bit) 
11.23 (PA-RISC) (64bit) 
11.31 (PA-RISC) (64bit)(10/30) 
11.22, 11.23, 11.31 (IA64 – Itanium) 
Note: for all Itanium systems using “Montecito” processors, refer tonote:400227.1 for special installation instructions

11.0 (64bit) 
11.11 (64bit)

11.0, 11.11(11i) (32bit/64bit)

11.0, 11.11(11i) (32bit/64bit)

11.0, 11.11(11i) (32bit/64bit)

10.20 (32bit) 
11.0, 11.11(11i) (32bit/64bit)

10.20 (32bit) 
11.0 (32 or 64)

HP Disk Space

1.7G database 
6.9 G Software

1.7G Database 
6.9G Software

1.2G Database 
2.5G Software 
1G Companion 
150M-1.5G Client

1.2G Database 
2.5G Software 
1G Companion 
150M-1.5G Client

4.5G

3.5G

1.5G

910Mb

900Mb

900Mb

900Mb

HP RAM

Database: minimum 1GB, recommended 2GB

Grid Infrastructure for standalone server: minimum 1.5GB (plus another 1GB if installing Database too), recommended 4GB

1GB

1GB

512Mb 
256Mb(Client/Compan)

512Mb

256Mb

256Mb

128Mb

128Mb

64Mb or 
128Mb / 
ConText

32Mb or 
128Mb / 
ConText

HP swap

Between 1 GB and 2 GB then 1.5 times RAM. 
Between 2 GB and 16 GB then equal to RAM. 
More than 16 GB then 16 GB RAM.

If RAM = 1GB to 2GB 
then 1.5 times RAM 
elseif RAM > 2GB and < 8GB 
then match RAM 
else RAM > 8GB 
then .75 times RAM

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

1Gb or match RAM 
512Mb(Client/Compan)

1Gb or match RAM

2*RAM

2*RAM

2*RAM

3*RAM

3*RAM

3*RAM

HP tmp

1GB

400Mb

400Mb

400Mb

400Mb

400Mb

75Mb

?

75Mb

50Mb

50Mb

HP jdk & JRE

HPUX JDK 6.0.05, HPUX JDK 5.0.15

NOTE: The JDK version included with 11.2.0.3 on HP-UX Itanium (1.5.0.23) is not compatible with Itanium 2 model 9310 processors. Please refer to the statement at the end of bothNote:404843.1 and Note:552358.1. To workaround the issue, download JDK 1.5.0.24 or higher and use the “./runInstaller -jreLoc …” syntax to start the 11.2.0.3 installation.

Java 1.5.0.0.6 is installed

Java SDK 1.4.2.00 is installed

Java SDK 1.4.2.00 is installed

JDK 1.3.1.02

JDK 1.2.2.07 & 1.1.8

JDK 1.2.2 & 1.1.8.03

1.1.8.10

1.1.7

n/a

n/a

HP Patches/ 
Packages
 

“s/b” indicates superseded by

See Note 43507.1 for other applicable patches.

For HP-UX 11i V3 (11.31): 
PHCO_40381 11.31 Disk Owner Patch
PHCO_41479 11.31 (fixes an 11.2.0.2 ASM disk discovery issue) 
PHKL_38038 VM patch – hot patching/Core file creation directory 
PHKL_38938 11.31 SCSI cumulative I/O patch 
PHKL_39351 Scheduler patch : post wait hang 
PHSS_36354 11.31 assembler patch 
PHSS_37042 11.31 hppac (packed decimal) 
PHSS_37959 Libcl patch for alternate stack issue fix (QXCR1000818011) 
PHSS_39094 11.31 linker + fdp cumulative patch 
PHSS_39100 11.31 Math Library Cumulative Patch 
PHSS_39102 11.31 Integrity Unwind Library 
PHSS_38141 11.31 aC++ Runtime 
Pro*C/C++, Oracle Call Interface, Oracle C++ 
Pro*C/C++, Oracle Call Interface, Oracle C++ Call Interface, Oracle XML Developer’s Kit (XDK):- 

Patch for HP-UX 11i V3 (11.31) on HP-UX Itanium:- 
PHSS_39824 – 11.31 HP C/aC++ Compiler (A.06.23) patch 
PHKL_40941 – Scheduler patch : post wait hang

For HP-UX PA-RISC and Itanium 11.23 (Mar ’07 Patch bundle for HP-UX 11iV2- B.11.23.0703): 
PHSS_35979 s/b PHSS_37201 s/b PHSS_37492 s/b PHSS_38134 
PHSS_35978 s/b PHSS_36343 s/b PHSS_38140 
PHCO_35524 s/b PHCO_36744 
PHKL_35478 s/b PHKL_36319 
PHCO_36673 s/b PHCO_37228 
PHKL_35029 s/b PHKL_37121 
PHKL_37809 or later Note 580273.1

For HP-UX PA-RISC and Itanium 11.31: 
PHKL_35900 
PHKL_36248 
PHKL_36249 
PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38038 
PHKL_38397 or later. Note 580273.1

Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test

Refer to the following Web site for information about additional java patches:http://www.hp.com/products1/unix/java/patches/index.htmlThe default 64bit OS (PA-RISC and Itanium From Bug 8789180) installation does not create a few required X library symbolic links. The following symbolic links need to be created: 
(NOTE: This task is required only if the Motif 2.1 Development Environment Package ( X11MotifDevKit.MOTIF21-PRG ) is not installed ). 
cd /usr/lib 
ln -s /usr/lib/libX11.3 libX11.sl 
ln -s /usr/lib/libXIE.2 libXIE.sl 
ln -s /usr/lib/libXext.3 libXext.sl 
ln -s /usr/lib/libXhp11.3 libXhp11.sl 
ln -s /usr/lib/libXi.3 libXi.sl 
ln -s /usr/lib/libXm.4 libXm.sl 
ln -s /usr/lib/libXp.2 libXp.sl 
ln -s /usr/lib/libXt.3 libXt.sl 
ln -s /usr/lib/libXtst.2 libXtst.sl

Per HP Bug (Doc ID: KBRC00003627) 
NOTE: This bug is not applicable to 11.23 The default 64bit OS (PA-RISC and Itanium) installation does not create a few required X library symbolic links. The following symbolic links need to be created: 
(NOTE: This task is required only if the Motif 2.1 Development Environment Package ( X11MotifDevKit.MOTIF21-PRG ) is not installed ). 
cd /usr/lib 
ln -s /usr/lib/libX11.3 libX11.sl 
ln -s /usr/lib/libXIE.2 libXIE.sl 
ln -s /usr/lib/libXext.3 libXext.sl 
ln -s /usr/lib/libXhp11.3 libXhp11.sl 
ln -s /usr/lib/libXi.3 libXi.sl 
ln -s /usr/lib/libXm.4 libXm.sl 
ln -s /usr/lib/libXp.2 libXp.sl 
ln -s /usr/lib/libXt.3 libXt.sl 
ln -s /usr/lib/libXtst.2 libXtst.sl

GOLDQPK11i, December 2004 or later 
If GOLDQPK is not installed then these two patchkits need to be installed: 
GOLDAPPS11i, December 2004 or later 
GOLDBASE11i, December 2004 or later

11.11 required patches: 
o PHNE_31097 s/b PHNE_32477 s/b PHNE_33498 s/b PHNE_35418 s/b PHNE_36168 s/b PHNE_37110 
o PHSS_31221 s/b PHSS_33263 s/b PHSS_33944 s/b PHSS_33945 
For JDK, refer to HP Java for latest patches: 
o PHSS_30970 s/b PHSS_33033 s/b PHSS_35379 s/b PHSS_35385 
For PL/SQL/ProC,OCI,OCCI,XDK: 
o PHSS_32508 s/b PHSS_34411 s/b PHSS_35099 s/b PHSS_36087 
o PHSS_32509 s/b PHSS_34412 s/b PHSS_35098 s/b PHSS_36086 
o PHSS_32510 s/b PHSS_34413 s/b PHSS_35100 s/b PHSS_36088

11.23 (PA-RISC) required patches: 
o PHSS_31849 s/b PHSS_37021 s/b PHSS_37492 s/b PHSS_40537 
o PHSS_31852 s/b PHSS_35055 s/b PHSS_36343s/b PHSS_38140 
For PL/SQL/ProC,OCI,OCCI,XDK: 
o PHSS_32511 
o PHSS_32512 
o PHSS_32513 
o PHKL_37809 or later Note 580273.1

Ensure that unzip version is 5.5 or higher ($ unzip -v) [reference Note 263692.1], if not it can be downloadedhere

11.31 (PA-RISC) required patches: 
o PHKL_35900: 11.31 evacd performance, kvaddr leak panic 
o PHKL_36248: 11.31 esctl cumulative patch 
o PHKL_36249: 11.31 esdisk cumulative patch 
o PHKL_38397 or later Note 580273.1 
o PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38038: 11.31 call to read(2) or write(2) may incorrectly return -1 
o You can use HP JDK 5.0.07 with the Oracle Java Database Connectivity and Oracle Call Interface drivers. Ensure that you install the patch PHKL_35029 s/b PHKL_37121 to use JDK 5.0.07.

11.23 (Itanium) required patches: 
The following operating system patches: 
o BUNDLE11i B.11.23.0409.3: Patch Bundle for HP-UX 11i V2 
Note: You must have the August 2004 version of BUNDLE11i B.11.23.0408.1 for HP-UX 11i v2 on your system prior to updating to the HP-UX 11i v2 September 2004 or later release. 
o PHCO_32426 
o PHKL_32646 s/b PHKL_36103 
o PHKL_32632 s/b PHKL_33656 s/b PHKL_33807 s/b PHKL_38364 
o PHKL_32645 s/b PHKL_34477 s/b PHKL_37106 
o PHKL_33552 s/b PHKL_33563 s/b PHKL_36667 s/b PHKL_37653 s/b PHKL_41002 
o PHSS_31850 s/b PHSS_34040 s/b PHSS_37201 s/b PHSS_37492 s/b PHSS_38134 s/b PHSS_40537 
o PHSS_31851 s/b PHSS_34043 s/b PHSS_34859 s/b PHSS_37498 s/b PHSS_38138 or PHSS_39101 s/b PHSS_40541 
o PHSS_31854 s/b PHSS_33357 s/b PHSS_34045 s/b PHSS_34445 s/b PHSS_40547 
o PHSS_31855 s/b PHSS_33350 s/b PHSS_34041 s/b PHSS_35055 s/b PHSS_36343 s/b PHSS_38140 s/b PHSS_40543 
o PHSS_33275 s/b PHSS_33349 s/b PHSS_34040 s/b PHSS_37201 s/b PHSS_37492 s/b PHSS_38134 s/b PHSS_40537 
o PHSS_33276 s/b PHSS_34042 s/b PHSS_34853 s/b PHSS_36344 s/b PHSS_40539 
o PHKL_37809 or later Note 580273.1

For PL/SQL native compilation and installation of Pro*C/C++, Oracle Call Interface, Oracle C++ Call Interface, or Oracle XML Developer’s Kit (XDK) , the following patches are required: 
o PHSS_33278 
o PHSS_33277

The following JDK patches: 
o PHCO_31553 s/b PHCO_33675 s/b PHCO_36323 s/b PHCO_37940 s/b PHCO_39699 
o PHKL_31500 
o PHSS_32213 s/b PHSS_32502 s/b PHSS_34201 s/b PHSS_37492 s/b PHSS_40537 
Note: Refer to the following Web site for information about additional patches that may be required by JDK 1.4.2: 
HP Java Patches

11.31 (Itanium) required patches: 
The following operating system patches: 
o PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38449 s/b PHKL_38038 
o PHKL_38397 or later Note 580273.1 

The following patches are supported on Oracle Database 10g release 2:(Part Number B25292-06) 
PHKL_35900: 11.31 evacd performance, kvaddr leak panic 
PHKL_36248: 11.31 esctl cumulative patch 
PHKL_36249: 11.31 esdisk cumulative patch 
PHKL_35936: 11.31 call to read(2) or write(2) may incorrectly return -1 

Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test

Per HP Bug (Doc ID: KBRC00003627) 
NOTE: This bug is not applicable to 11.23 The default 64bit OS installation does not create a few required X library symbolic links. The following symbolic links need to be created: 
(NOTE: This task is required only if the Motif 2.1 Development Environment Package ( X11MotifDevKit.MOTIF21-PRG ) is not installed ). 
cd /usr/lib 
ln -s /usr/lib/libX11.3 libX11.sl 
ln -s /usr/lib/libXIE.2 libXIE.sl 
ln -s /usr/lib/libXext.3 libXext.sl 
ln -s /usr/lib/libXhp11.3 libXhp11.sl 
ln -s /usr/lib/libXi.3 libXi.sl 
ln -s /usr/lib/libXm.4 libXm.sl 
ln -s /usr/lib/libXp.2 libXp.sl 
ln -s /usr/lib/libXt.3 libXt.sl 
ln -s /usr/lib/libXtst.2 libXtst.sl

GOLDQPK11i, June 2003 or later 
If GOLDQPK is not installed then these two patchkits need to be installed: 
GOLDAPPS11i, June 2003 or later 
GOLDBASE11i, June 2003 or later 
Jun03GQPK11i_Aux_Patch (Does not exist, see Bug 3512068)

X11MotifDevKit (spatial only) 
o PHCO_28123 s/b PHCO_31314 s/b PHCO_32397 
o PHKL_29198 s/b PHKL_32603 
o PHNE_28476 s/b PHNE_29825 s/b PHNE_30367 s/b PHNE_31091 s/b PHNE_33729 
o PHNE_28923 s/b PHSS_30049 s/b PHNE_32396 s/b PHNE_33704 
o PHSS_28871 s/b PHSS_33033 
o PHSS_28880 s/b PHSS_32573 s/b PHSS_33263 
o PHCO_26331 s/b PHCO_27958 s/b PHCO_33205 
o PHCO_29109 s/b PHCO_29960 s/b PHCO_30544 
o PHKL_25468 s/b PHKL_30542 
o PHKL_25842 s/b PHKL_30288 s/b PHKL_34311 
o PHKL_25993 
o PHKL_25994 s/b PHKL_32061 s/b PHKL_34309 
o PHKL_25995 s/b PHKL_30541 s/b PHKL_32457 s/b PHKL_34024 
o PHKL_26468 s/b PHKL_27316 s/b PHKL_30837 
o PHKL_28489

HP-UX 11.23 (IA64) Operating System Patches
o PHSS_29658 s/b PHSS_30015 s/b PHSS_30237 
o PHSS_29660

Java SDK 1.4.2 latest patches

Ensure that unzip version is 5.5 or higher ($ unzip -v) [reference Note 263692.1], if not it can be downloaded here

11.31 (Itanium) required patches: 
The following operating system patches: 
PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38038 
Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test

Per HP Bug (Doc ID: KBRC00003627) 
NOTE: This bug is not applicable to 11.22,11.23 The default 64bit OS installation does not create a few required X library symbolic links. The following symbolic links need to be created: 
cd /usr/lib 
ln -s /usr/lib/libX11.3 libX11.sl 
ln -s /usr/lib/libXIE.2 libXIE.sl 
ln -s /usr/lib/libXext.3 libXext.sl 
ln -s /usr/lib/libXhp11.3 libXhp11.sl 
ln -s /usr/lib/libXi.3 libXi.sl 
ln -s /usr/lib/libXm.4 libXm.sl 
ln -s /usr/lib/libXp.2 libXp.sl 
ln -s /usr/lib/libXt.3 libXt.sl 
ln -s /usr/lib/libXtst.2 libXtst.sl

HP-UX 11.0(64 bit) Operating System Patches: 
Sept 2001 Quality Pack 
o PHCO_23792 s/b PHCO_26960 
o PHCO_24148 s/b PHCO_25707 s/b PHCO_27608 s/b PHCO_28425 s/b PHCO_32448 
o PHKL_24268 s/b PHKL_27178 (has been recalled by HP may destroy logical volumes on PVGs – more info s/b PHKL_32920 
o PHKL_24729 s/b PHKL_29256 
o PHKL_25475 s/b PHKL_27510 s/b PHKL_30553 
o PHKL_25525 s/b PHKL_27364 s/b PHKL_28766 s/b PHKL_31867 
o PHNE_24715 s/b PHNE_26771 s/b PHNE_29473 s/b PHNE_32041 s/b PHNE_33395 
o PHSS_23670 s/b PHSS_26138 s/b PHSS_27858 
o PHSS_24301 s/b PHSS_26273 s/b PHSS_28433 (only needed for C++ compiler and Pro*C++) 
o PHSS_24303 s/b PHSS_26559 s/b PHSS_30965 
o PHSS_24627 s/b PHSS_26945 s/b PHSS_32574 
o PHSS_22868 (only needed for C++ compiler and Pro*C++)

Ensure that unzip version is 5.5 or higher ($ unzip -v) [reference Note 263692.1], if not it can be downloaded here

HP-UX 11i (64 Bit) Operating System Patches: 
Support Plus Bundle ‘December 2002 SP-0212’ or later 
JDK 1.3.1.02 
o PHCO_24402 s/b PHCO_25569 s/b PHCO_31923 
o PHCO_28427 s/b PHCO_29029 s/b PHCO_31903 s/b PHCO_33533 
o PHKL_25506 s/b PHKL_33457 
o PHNE_27144 s/b PHNE_27745 s/b PHNE_30580 (For RAC systems) 
o PHNE_28568 s/b PHNE_30378 s/b PHNE_32477 s/b PHNE_33315 
o PHSS_26263 s/b PHSS_26560 s/b PHSS_33033 
o PHSS_24638 s/b PHSS_26946 s/b PHSS_30966 s/b PHSS_33263 
o PHSS_26774 s/b PHSS_28849 s/b PHSS_30742 (For ServiceGuard 11.13 systems)

HP-UX 11.22 /11.23 (IA64) Operating System Patches: 
o PHSS_27284 s/b PHSS_28977 
o PHSS_27285 s/b PHSS_28970 
o PHSS_27286 s/b PHSS_28978 
o PHSS_27287 s/b PHSS_29652 
o PHSS_27288 s/b PHSS_28971 
o PHSS_27289 s/b PHSS_29653 
o PHSS_27290 s/b PHSS_28973 
o PHSS_27291 s/b PHSS_28969 
o PHSS_27292 s/b PHSS_29654 
o PHSS_27293 s/b PHSS_28975 
o PHKL_28465

11.31 (Itanium) required patches: 
The following operating system patches: 
PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38038 
Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test

HP-UX 11.0(64 bit) Operating System Patches: 
Dec 2000 patch bundle 
o PHCO_23092 s/b PHCO_23963 s/b PHCO_26111 
o PHCO_23770 s/b PHCO_25707 s/b PHCO_27608 
o PHCO_23919 s/b PHCO_27340 
o PHKL_18543 
o PHKL_23226 s/b PHKL_27510 s/b PHKL_30553 
o PHKL_23813 s/b PHKL_25525 s/b PHKL_27364 s/b PHKL_31867 
o PHKL_23814 s/b PHKL_24729 s/b PHKL_29256 
o PHKL_23815 s/b PHKL_26337 s/b PHKL_27553 
o PHKL_23857 s/b PHKL_25525 s/b PHKL_27364 s/b PHKL_31867

HP-UX 11i (64 bit) Operating System Patches Status 
o PHCO_23094 s/b PHCO_24402 
o PHCO_23772 s/b PHCO_26124 s/b PHCO_27910 
o PHSS_23441 s/b PHSS_26263 
o PHNE_23502 s/b PHNE_25625 s/b PHNE_26388 s/b PHNE_28568

11.0 patches: 
o PHSS_21947 s/b PHSS_24303 s/b PHSS_26559 
o PHNE_20316 s/b PHNE_22566 s/b PHNE_25440 
o PHKL_21392 s/b PHKL_24027 
o PHKL_22145 s/b PHKL_25475 s/b PHKL_27510 s/b PHKL_30553 
o PHKL_22266 s/b PHKL_27178

DART 49, 6/00

Patch Bundle9905 
o PHCO_17556 s/b PHCO_23651
o PHCO_17792 s/b PHCO_21187 s/b PHCO_25902
o PHCO_18229 s/b PHCO_23963 s/b PHCO_26111
o PHCO_19491 s/b PHCO_25707 s/b PHCO_27608
o PHCO_19666 s/b PHCO_23792 s/b PHSS_26960 
o PHKL_14750 s/b PHKL_25475 s/b PHKL_27510 s/b PHKL_30553 
o PHKL_17038 s/b PHKL_25525 s/b PHKL_27364 s/b PHKL_31867 
o PHKL_18543 
o PHKL_19800 s/b PHKL_24027 
o PHKL_20016 
o PHKL_20079 s/b PHKL_24027 
o PHNE_19616 s/b PHNE_24100 s/b PHNE_25385 
o PHSS_14582 s/b PHSS_26320 
o PHSS_15853 s/b PHSS_23546 s/b PHSS_26566 
o PHSS_16849 s/b PHSS_25718 s/b PHSS_27469 
o PHSS_17535 s/b PHSS_25091 
o PHSS_18066 
o PHSS_18110 s/b PHSS_26273 s/b PHSS_28433 
o PHSS_18430 s/b PHSS_25199 s/b PHSS_26495 
o PHSS_18649 s/b PHSS_26320 
o PHSS_19593 s/b PHSS_25447 s/b PHSS_27230 
o PHSS_19178 s/b PHSS_25249 
o PHSS_19748 s/b PHSS_25149 s/b PHSS_26490 
o PHSS_19866 s/b PHSS_24303 s/b PHSS_26559 
o PHSS_20544 s/b PHSS_26138 s/b PHSS_27858 
o PHSS_20014 s/b PHSS_24303 s/b PHSS_26559 
o PHSS_21180

PHKL_14750 s/b PHKL_25475 s/b PHKL_27510 s/b PHKL_30553 
o PHKL_17709 s/b PHKL_23792 s/b PHKL_26960 
o PHKL_17869 s/b PHKL_18543 
o PHNE_17446 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473

32/64bit 11.0 
o PHNE_15995 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473 
o PHNE_16283 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473

64bit 11.0 
o PHSS_15316 s/b PHSS_24303 s/b PHSS_26559
o PHSS_16404 s/b PHSS_24303 s/b PHSS_26559

32/64bit 11.0 
o PHNE_15995 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473 
o PHNE_16283 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473

64bit 11.0 
o PHSS_15316 s/b PHSS_24303 s/b PHSS_26559
o PHSS_16404 s/b PHSS_24303 s/b PHSS_26559

HP Kernel Settings

Refer to the 11GR2 HP-UX Install Guide for steps to do this. Section 2.10 Configuring Kernel Parameters on HP-UX Systems.Part Number E24336-02.

Important: For HP 9000/700 workstations Only, see Note 467166.1
set the following before starting the OUI,DBCA, or DBUA: 
$ export JAVA64FLAG=”-d64″

KSI_ALLOC_MAX (NPROC*8) 
EXECUTABLE_STACK=0 
MAX_THREAD_PROC 1024 
MAXDSIZ 1073741824 
MAXDSIZ_64BIT 2147483648 
MAXFILES 65536 Note:1061351.1 
MAXFILES_LIM 65536 Note:1061351.1 
MAXTSIZE_64BIT 1073741824 
MAXSSIZ 134217728 bytes 
MAXSSIZ_64BIT 1073741824 
MAXUPRC ((NPROC*9)/10)+1 Bug 6995956 
MSGMAP (MSGTQL+2) * 
MSGMNI (NPROC) 
MSGSEG 32767 * 
MSGTQL (NPROC) 
NCSIZE (NINODE+1024) 
NFILE (15*NPROC+2048) * 
NFLOCKS (NPROC) 
NINODE (8*NPROC+2048) 
NKTHREAD (((NPROC*7)/4)+16) 
NPROC 4096 
SEMMNI (NPROC) 
SEMMNS (SEMMNI*2) 
SEMMNU (NPROC – 4) 
SEMVMX 32767 
SHMMAX AvailMem 
SHMMNI 4096 
SHMSEG 512 
VPS_CEILING 64

* MSGMAP,MAXSWAPCHUNKS, NCALLOUT, SEMMAP,VX_NCSIZE,NFILE, MSGSEG are obsolete on 11.31 (Itanium and PA-RISC) and no longer required to be set.

KSI_ALLOC_MAX (NPROC*8) 
EXECUTABLE_STACK=0 
MAX_THREAD_PROC 1024 
MAXDSIZ 1073741824 bytes 
MAXDSIZ_64BIT 2147483648 bytes 
MAXFILES 65536 Note:1061351.1 
MAXFILES_LIM 65536 Note:1061351.1 
MAXSSIZ 134217728 bytes 
MAXSSIZ_64BIT 1073741824 
MAXSWAPCHUNKS 16384* 
MAXUPRC ((NPROC*9)/10)+1 Bug 6995956 
MSGMAP (MSGTQL+2) 
MSGMNI (NPROC) 
MSGSEG 32767 
MSGTQL (NPROC) (B25293-01) 
NCSIZE (NINODE+1024)* 
NFILE (15*NPROC+2048) 
NFLOCKS (NPROC) (B25293-01) 
NINODE (8*NPROC+2048) 
NKTHREAD (((NPROC*7)/4)+16) 
NPROC 4096 
SEMMAP (SEMMNI+2)* 
SEMMNI (NPROC) (B25293-01) 
SEMMNS (SEMMNI*2) 
SEMMNU (NPROC – 4) 
SEMVMX 32767 
SHMMAX AvailMem 
SHMMNI 512 
SHMSEG 120 
VPS_CEILING 64

* MAXSWAPCHUNKS, SEMMAP, and VX_NCSIZE are obsolete on 11.23 PA-RISC and IPF and no longer need to be set 
Set NCSIZE = (NINODE+1024)

11.31 (Itanium and PA-RISC)
The following 11.31 kernel parameters are obsolete: 
maxswapchunks, msgmap, ncallout, semmap, and vx_ncsize,Nfile,Msgseg

KSI_ALLOC_MAX (NPROC*8) 
MAX_THREAD_PROC 256 
MAXDSIZ 1073741824 bytes 
MAXDSIZ_64BIT 2147483648 bytes 
MAXSSIZ 134217728 bytes 
MAXSSIZ_64BIT 1073741824 
MAXSWAPCHUNKS 16384* 
MAXUPRC ((NPROC*9)/10)+1 Bug 6995956 
MSGMAP (2+MSGMNI) 
MSGMNI (NPROC) 
MSGSEG 32767 
MSGTQL (NPROC) 
NCSIZE (NINODE+VX_NCSIZE)* 
NFILE (15*NPROC+2048) 
NFLOCKS (NPROC) 
NINODE (8*NPROC+2048) 
NKTHREAD (((NPROC*7)/4)+16) 
NPROC 4096 
SEMMAP (SEMMNI+2)* 
SEMMNI (NPROC) 
SEMMNS (SEMMNI*2) 
SEMMNU (NPROC – 4) 
SEMVMX 32768 
SHMMAX AvailMem 
SHMMNI 512 
SHMSEG 120 
VPS_CEILING 64

* MAXSWAPCHUNKS, SEMMAP, and VX_NCSIZE are obsolete on 11.23 PA-RISC and IPF and no longer need to be set 
Set NCSIZE = (NINODE+1024)

11.31 (Itanium and PA-RISC)
The following 11.31 kernel parameters are obsolete: 
maxswapchunks, msgmap, ncallout, semmap,vx_ncsize,Nfile and Msgseg

KSI_ALLOC_MAX (NPROC*8) 
MAX_THREAD_PROC 256 
MAXDSIZ 1073741824 bytes 
MAXDSIZ_64BIT 2147483648 bytes 
MAXSSIZ 134217728 bytes 
MAXSSIZ_64BIT 1073741824 
MAXSWAPCHUNKS 16384* 
MAXUPRC ((NPROC*9)/10) 
MSGMAP (MSGTQL+2) 
MSGMNI (NPROC) 
MSGSEG 32767 
MSGTQL (NPROC) 
NCALLOUT (NKTHREAD+16)* 
NCSIZE ((8*NPROC+2048)+VX_NCSIZE)* 
NFILE (15*NPROC+2048) 
NFLOCKS (NPROC) 
NINODE (8*NPROC+2048) 
NKTHREAD (((NPROC*7)/4)+16) 
NPROC 4096 
SEMMAP (SEMMNI+2)* 
SEMMNI (NPROC) 
SEMMNS (SEMMNI*2) 
SEMMNU (NPROC – 4) 
SEMVMX 32768 
SHMMAX AvailMem 
SHMMIN 1 
SHMMNI 512 
SHMSEG 32 
VPS_CEILING 64

* MAXSWAPCHUNKS, SEMMAP, NCALLOUT, and VX_NCSIZE are obsolete on 11.23 PA-RISC and IPF and no longer need to be set 
Set NCSIZE = (NINODE+1024)

11.31 (Itanium and PA-RISC)
The following 11.31 kernel parameters are obsolete: 
maxswapchunks, msgmap, ncallout, semmap,vx_ncsize,Nfile and Msgseg

SHMMAX AvailMem 
SHMMIN 1 
SHMMNI 512 
SHMSEG 32 
SEMMNI 8192 
SEMMNS 16384

MAXDSIZ 
1073741824 bytes

MAXDSIZ_64BIT 
2147483648 bytes

MAXSSIZ 
134217728 bytes

MAXSSIZ_64BIT 
1073741824

SHMMAX 1GB 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 70 
SEMMNS 200

nflocks = 200 + sum of the values of init.ora parameterdb_files for all instances of oracle onthe machine.

MAX_THREAD_PROC = 256 or more

maxdsiz 
1Gb (1073741824) 0x40000000

maxdsiz_64bit 
1.6Gb (1717986918) 66666666

maxssiz 
200mb (209715200) C800000

maxssiz_64bit 
200mb (209715200) C800000

maxtsiz 
1Gb (1073741824) 0x40000000

maxtsiz_64bit 
1Gb (1073741824) 0x40000000

SHMMAX 1GB 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 70 
SEMMNS 200 
maxdsiz and maxdsiz_64bit must be >= 128Mb

SHMMAX 1GB 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 70 
SEMMNS 200 
maxdsiz and maxdsiz_64bit must be >= 128Mb

SHMMAX 1GB 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 70 
SEMMNS 200 
maxdsiz and maxdsiz_64bit must be >= 128Mb

SHMMAX 1GB 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 70 
SEMMNS 200

maxdsiz and maxdsiz_64bit must be >= 128Mb

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

Oracle Solaris
(32-bit and 64-bit stands for Oracle DB, not OS)

Solaris(64bit) 10 (update 6 or higher), Solaris 11

NOTE: On Solaris 11, only 11.2.0.3 is certified (not 11.2.0.1 or 11.2.0.2)

Set the following variable before installing 11.2.0.3 on Solaris 11: 
export AWT_TOOLKIT=XToolkit

2.9 Update 7 (09/04), 2.10

  • 2.8 Update 7 (02/02), 2.9 Update 6 (04/04), 2.10 (64bit)
  • Solaris 10 on AMD64/x86_64

Solaris SPARC 2.8, 2.9 (64bit) 
o Solaris SPARC 10 (64bit) requires 10.1.0.3.0 patchset 
o Solaris x86 2.9, 10

o 2.6, 2.7, 2.8, 2.9 (32bit) 
o Solaris 10 (32bit) requires 9.2.0.4.0 patchset 
o 2.8, 2.9 (64bit) 
o Solaris 10 (64bit) requires 9.2.0.6.0 patchset

o 2.6, 2.7, 2.8, 2.9 (32bit) 
o 2.8, 2.9 (64bit)

o 2.6, 2.7, 2.8, 2.9 (32bit) 
o 2.8, 2.9 (64bit)

o 2.6, 2.7, 2.8 (32bit) 
o 2.7, 2.8 (64bit)

2.6, 2.7, 2.8 (32bit) 
o 2.7 (64bit)

2.5.1, 2.6, 2.7, 2.8

2.5.1, 2.6, 2.7, 2.8

Solaris Disk Space

1.5 to 2G Database 
4.7G Software

1.5 to 2G Database 
4.7G Software

1.2G Database 
1.5G – 3.5G Software 
1G Companion 
150M-1G Client

1.2G Database 
1.5G Software 
1G Companion 
150M-1G Client

4.5G

3.5G (32bit) 
5.7G (64bit)

1355Mb

1170Mb

811Mb

600Mb

600Mb

Solaris RAM

Database: minimum 1GB, recommended 2GB

Grid Infrastructure for standalone server: minimum 1.5GB (plus another 1GB if installing Database too), recommended 4GB

1GB

1GB

512Mb 
256Mb(Client/Compan)

512Mb

256Mb (32bit) 
512Mb (64bit)

128Mb

128Mb

128Mb

64Mb or 
128Mb / 
ConText

32Mb or 
128Mb / 
ConText

Solaris swap

If RAM = 1 GB to 2 GB 
then 1.5 times RAM 
elseif RAM = 2 GB and 16 GB 
then match RAM 
else RAM > 16 GB 
then 16 GB 

Note: On Oracle Solaris, if you use non-swappable memory, such as ISM, then you should deduct the memory allocated to this space from the available RAM before calculating swap space. If you plan to install Oracle Database or Oracle RAC on systems using DISM, then available swap space must be at least equal to the sum of the SGA sizes of all instances running on the servers.

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

1Gb or match RAM 
512Mb(Client/Compan)

1Gb or match RAM

400Mb

2*RAM or 
400Mb

2*RAM or 
400Mb

2*RAM

3*RAM

3*RAM

Solaris tmp

1GB

275Mb

400Mb

400Mb

400Mb

400Mb

?

?

?

20Mb

20Mb

Solaris JDK & JRE

JDK 6 Update 10 (Java SE Development Kit 1.6 u10) or JDK 5 (1.5.0_16)

JDK 1.5.0_11 is installed

JDK 1.4.2_01 is installed 
JDK 1.4.2_08 is installed (x86_64)

JDK 1.4.2_01 is installed

JDK 1.3.1_02 & 1.1.8_12 (32bit) 1.1.8_15 (64bit)

JDK 1.2.2_07 & 1.1.8_12

JDK 1.2.2. & 1.1.8_10

1.1.8_10

?

n/a

n/a

Solaris Patches/ 
Packages

Required packages Solaris 10: 
SUNWarc 
SUNWbtool 
SUNWhea 
SUNWlibC 
SUNWlibm 
SUNWlibms 
SUNWmfrun 
SUNWsprot 
SUNWtoo 
SUNWi1of 
SUNWi1cs (ISO8859-1) 
SUNWi15cs (ISO8859-15) 
SUNWxwfnt 
SUNWcsl 

Although it is not listed in the Install Guide, the RAC root.sh script requires /usr/xpg4/bin/tr and so requires the SUNWxcu4 package. 
@ See Bug:14046807 for confirmation. 

For Solaris 11 all packages are installed by default. Hence no additional packages are required (refer Installation Document). But it is suggested to make sure above packages are installed or its equivalent are installed. We can search for packages at Oracle Solaris 11 Package repository). To fix the issue reported in Bug 14046807 install XCU4 Utilities 

Note : From Solaris 11, the SUNW prefix for package names is no longer used. With the introduction of IPS, all software packages are renamed. for more information refer to Oracle Solaris 10 SVR4 and IPS Package Comparison 

Information on Solaris 11 Installation types – refer to Note 1557986.1

Important: For non-sun4u or sun4v workstations Only, see Note 467166.1
set the following before starting the OUI,DBCA, or DBUA: 
$ export JAVA64FLAG=”-d64″

Required Packages: 
SUNWarc 
SUNWbtool 
SUNWhea 
SUNWi15cs 
SUNWi1cs 
SUNWi1of 
SUNWlibC 
SUNWlibm 
SUNWlibms 
SUNWmfrun 
SUNWsprot 
SUNWsprox (Not applicable to Solaris 10), 
SUNWtoo 
SUNWxwfnt 
SUNWuiu8 Note 290034.1 
SUNWulcf Note 290034.1 

Although it is not listed in the Install Guide, the RAC root.sh script requires /usr/xpg4/bin/tr and so requires the SUNWxcu4 package. 
@ See Bug:14046807 for confirmation.

Solaris 9 Reqd Patches: 
112233-11 
111722-04 
112874-39 
115675-01 (NUMA only) 
113471-08 (NUMA only) 
115675-01 (NUMA only) 
113029-07 for Fair Share Scheduler, See Note 558374.1

Solaris 10 Reqd Patches: 
127111-02 s/b 127127-11 
137111-04 s/b 137137-09 (Part Number B32314-02)

To support Pro*C/C++,Pro*FORTRAN,Oracle Call Interface,Oracle C++ Call Interface,Oracle XML Developers Kit (XDK) 
112760-05 (Solaris 9) 
117837-05 (Solaris X86 10) 
117846-08 (Solaris X86 10) 
118682-01 (Solaris X86 10) 
ulimit(TIME) to unlimited. Refer to Note 250262.1 
ulimit(FILE) to unlimited. Refer to Note 250262.1 
ulimit(DATA) to a minimum of 1048576. Refer to Note 250262.1 
ulimit(STACK) to a minimum of 32768. Refer to Note 250262.1 
ulimit(NOFILES) to a minimum of 4096. Refer to Note 250262.1 
ulimit(VMEMORY) to a minimum of 4194304. Refer to Note 250262.1

Required Packages: 
SUNWarc, 
SUNWbtool, 
SUNWhea, 
SUNWlibm, 
SUNWlibms, 
SUNWmfrun, 
SUNWsprot, 
SUNWsprox (Not applicable to Solaris 10), 
SUNWtoo, 
SUNWxwfnt, 
SUNWi1cs, 
SUNWi15cs, 
SUNWi1of, 
SUNWxcu4, 
SUNWuiu8 and SUNWulcf – See Note 290034.1

Solaris 8 Reqd Patches: 
108528-23 
108652-66 
108773-18 
108921-16 
108940-53 
108987-13 
108989-02 
108993-45 
109147-24 
110386-03 
111023-02 
111111-03 
111308-03 
111310-01 
112396-02 
111721-04 
112003-03 
112138-01 
112760-05 (Native PL/SQL,ProC,ProFortran,OCI,OCCI,XDK only) 
SUNWctplx/ SUNWdtbax/ SUNWtltkx/ SUNWtoox/ SUNWxwicx/ SUNWxwplx/ 
and also Patch 108940-76 (or higher) in order to fix the SUNWdtbax package Note 366100.1

Solaris 9 Reqd Patches: 
112233-11 
111722-04 (Bug 4122475
115675-01 
113471-08 
115675-01 
112760-05 (Native PL/SQL,ProC,ProFortran,OCI,OCCI,XDK only) 
112963-25 
113029-07 for Fair Scheduler, See Note 558374.1

Solaris 10 Reqd Patches 
127111-02 s/b 127127-11 for 10.2.0.4 or later (see README for 10.2.0.4.0) 
127111-03 s/b 127127-11 See Note 460424.1

Solaris 10 x86_64 Reqd Patches: 
118345-03 
119961-01 
127127-11 See Note 460424.1

Solaris 10 special instructions: 
Select ‘Do not create a starter database’ when installing Oracle 10gR2 due to Bug 4884705 and run the DBCA after the installation.

The Fair Share Scheduler(FSS) requires Solaris 10 11/06 or higher. 
If using a prior update of Solaris 10 install the following patches : 
Install patch 118833-36 before installing Oracle 10gR2 for Solaris 10 on SPARC. 
Install patch 118855-36 before installing Oracle 10gR2 for Solaris 10 on x86-64

IMPORTANT: Patch 4589082 needs to be installed prior to attempting an installation of 10.2 on Solaris 10 SPARC to avoid “Error in invoking target ‘relink’ of makefile ‘precomp/lib/ins_precomp.mk’ related to -ldce not found. See also Note 333348.1.

IMPORTANT: See Note 1190843.1regarding a related relinking issue in 10.2.0.5

Required Packages: 
SUNWarc, 
SUNWbtool, 
SUNWhea, 
SUNWlibC (CRS only) 
SUNWlibm, 
SUNWlibms, 
SUNWmfrun, 
SUNWsprot, 
SUNWsprox (Not applicable to Solaris 10), 
SUNWtoo, 
SUNWxwfnt, 
SUNWi1cs, 
SUNWi15cs, 
SUNWi1of 
SUNWuiu8,SUNWulcf (if Bug 4025250occurs) 
SUNWxcu4

Solaris 8 Reqd Patches: 
108528-23 
108652-66 
108773-18 
108921-16 
108940-53 
108987-13 
108989-02 
108993-18 
109147-24 
110386-03 
111023-02 
111111-03 
111308-03 
111310-01 
112396-02 
111721-04 
112003-03 
112138-01

Solaris 9 Reqd Patches: 
112233-11 
111722-04 (Bug 4122475
112963-25 
113029-07 for Fair Scheduler, See Note 558374.1

Solaris 10 special instructions: 
1. Execute runInstaller with the -ignoreSysPrereqs option. 
2. Select ‘Do not create a starter database’ when installing Oracle 10g. 
3. During installation, the warning message ‘SUNWsprox package not installed’ can be ignored as it is no longer provided separately. Press Continue to resume the installation. 
4. Download and install PSR 10.1.0.4 Patch 4163362(or apply PSR 10.1.0.3 Patch 3761843 and interim Patch 4163208(SPARC) or patch 4186426 (x86) from support.oracle.com. 
5. Download and install Patch 4365826from 10.1.0.3 or 10.1.0.4 from support.oracle.com. (SPARC only), also a merge patch containing 4365826 can be applied to 10.1.0.4.2 Patch 4590858 
6. If you have an End User Solaris 10 distribution, install the SUNWuiu8 package prior to installing the 10g client. 
7. The Fair Share Scheduler(FSS) requires Solaris 10 11/06 or higher. 
If using a prior update of Solaris 10 install the following patches : 
Install patch 118833-36 before installing Oracle 10gR2 for Solaris 10 on SPARC. 
Install patch 118855-36 before installing Oracle 10gR2 for Solaris 10 on x86-64 
8. Oracle Solaris 10 install Sun patch 127111-03 (SPARC) / 127127-11 (x86-64) See Note 460424.1

32bit/64bit 
SUNWarc, 
SUNWbtool, 
SUNWhea, 
SUNWlibm, 
SUNWlibms, 
SUNWmfrun, 
SUNWsprot, 
SUNWtoo 
SUNWi1of and SUNWxwfnt (for Java) 
SUNWsprox (for 64bit Oracle) (Not applicable to Solaris 10) 
SUNWuiu8,SUNWulcf (if Bug 4025250occurs) 
SUNWxcu4

108528-05 (2.8)

Solaris 10 special instructions: 
Execute runInstaller with the -ignoreSysPrereqs option 
The Fair Share Scheduler(FSS) requires Solaris 10 11/06 or higher. 
If using a prior update of Solaris 10 install the following patches : 
Install patch 118833-36 before installing Oracle 10gR2 for Solaris 10 on SPARC. 
Install patch 118855-36 before installing Oracle 10gR2 for Solaris 10 on x86-64 
Oracle Solaris 10 install Sun patch 127111-03 (SPARC) / 127127-11 (x86-64) See Note 460424.1

32bit/64bit 
SUNWarc, 
SUNWbtool, 
SUNWhea, 
SUNWlibm, 
SUNWlibms, 
SUNWsprot, 
SUNWtoo 
SUNWxcu4

Additional 
64bit 
SUNWarcx, 
SUNW2x (believe this is a typo and should be SUNWtoox)

108528-01 (2.8) 
105181-15 (2.6)

SUNWarc, 
SUNWbtool, 
SUNWhea, 
SUNWlibm, SUNWlibms, SUNWsprot, 
SUNWtoo 
SUNWxcu4

2.6 requires at least 105181-15

SUNWarc, 
SUNWbtool, 
SUNWhea, 
SUNWlibm, SUNWlibms, SUNWsprot, 
SUNWtoo

2.6 requires at least 105181-15

SUNWarc, 
SUNWbtool, SUNWlibm, SUNWlibms,SUNWsprot,
SUNWtoo, 
SUNWhea.

Sun 2.6 requires 105181-06

   

Solaris Kernel Settings


Refer to the 11g Solaris Install Guide. Part Number E24346-02 for steps to do this. 
Verifying UDP and TCP Kernel Parameters 

Note : In Solaris 11 to set TCP / UDP Kernel Parameter use ipadm command, ndd is deprecated in Solaris 11 
Refer to the for Comparison between ipadm and other networking commands

SEMMNI 100 
SEMMNS 1024(Obsolete) 
SEMMSL 256 
SEMVMX 32767(Obsolete) 
SHMMAX 4294967295 
SHMMNI 100 (Obsolete) 
NOEXEC_USER_STACK 1 
Note: For Solaris 10 Oracle recommends still setting all these values in the /etc/system file, as well as, the Resource Control Facility. 
Refer to the 11g Solaris Install Guide for steps to do this.

Here are the new names of the kernel parameters for Solaris 10 (Solaris 9 equivalents are in parentheses):

 project.max-sem-ids 100 (semmni)

 process.max-sem-nsems 256 (semmsl)

 project.max-shm-memory 4294967295 (shmmax)

 project.max-shm-ids 100 (shmmni)

SEMMNI 100 *** 
SEMMNS 1024 ** 
SEMMSL 256 *** 
SEMVMX 32767 ** 
SHMMAX 4294967295 
SHMMIN 1 * 
SHMMNI 100*** 
SHMSEG 10 * 
NOEXEC_USER_STACK 1 
* obsolete in Solaris 9 and 10 
** obsolete in Solaris 10 
*** default value in Solaris 10 is already larger 
Note: for Solaris 10 SHMMAX which is now set through the Resource Control Facility not /etc/system. Refer to the 10gR2 for Solaris SPARC Installation guide for steps to do this, as well as, the Release Notes which has corrections: 
10.2 Install Guides and Release Notes

Here are the new names of the kernel parameters for Solaris 10 (Solaris 9 equivalents are in parentheses):

 project.max-sem-ids 100 (semmni)

 process.max-sem-nsems 256 (semmsl)

 project.max-shm-memory 4294967295 (shmmax)

 project.max-shm-ids 100 (shmmni)

SEMMNI 100 *** 
SEMMNS 1024 ** 
SEMMSL 256 *** 
SEMVMX 32767 ** 
SHMMAX 4294967295 
SHMMIN 1 * 
SHMMNI 100*** 
SHMSEG 10 * 
NOEXEC_USER_STACK 1 
* obsolete in Solaris 9 and 10 
** obsolete in Solaris 10 
*** default value in Solaris 10 is already larger

SEMMNI 100 *** 
SEMMNS 1024 ** 
SEMMSL 256 *** 
SHMMAX 4294967295 
SHMMIN 1 * 
SHMMNI 100*** 
SHMSEG 10 * 
NOEXEC_USER_STACK 1 
* obsolete in Solaris 9 and 10 
** obsolete in Solaris 10 
*** default value in Solaris 10 is already larger

SEMMNI 100 
SEMMNS 256 
SEMMSL 256 
SHMMAX 4294967295 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10

SHMMAX 4294967295 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 100 
SEMMSL Set to 10 plus the largest PROCESSES parameter of any Oracle database on the system. 
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database, adding the largest one twice, then add an additional 10 for each database. 
SEMOPM 100 
SEMVMX 32767

SHMMAX 4294967295 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 100 
SEMMSL Set to 10 plus the largest PROCESSES parameter of any Oracle database on the system. 
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database, adding the largest one twice, then add an additional 10 for each database. 
SEMOPM 100 
SEMVMX 32767

SHMMAX 0.5*(physical memory present in machine) 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 100 
SEMMSL Set to 10 plus the largest initsid.ora PROCESSES parameter of an Oracle database on the system. 
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database except the largest one, plus 2 times the largest PROCESSES value, plus 10 times the number of Oracle databases. 
SEMOPM 100 
SEMVMX 32767

SHMMAX 4294967295 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNS 200 
SEMMNI 70 
SEMMSL Equal to or greater than the value of the 
PROCESSES initialization parameter.

SHMMAX 4294967295 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNS 200 
SEMMNI 70 
SEMMSL Equal to or greater than the value of the 
PROCESSES initialization parameter.

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

Tru64 OS 
do “/usr/sbin/sizer -v” to see specific version of Tru64, “uname -a” will not show it.

NA

Not Available

5.1b

5.1b

5.1a, 5.1b

5.0a, 5.1, 5.1a, 5.1b

4.0D-G, 5.0, 5.0a, 5.1, 5.1a, 5.1b(EV5.6 processor or higher) do ‘/usr/sbin/psrinfo -v’

4.0D-G, 5.0, 5.0a, 5.1

4.0D-G, 5.0, 5.0a, 5.1

4.0D-G, 5.0, 5.0a, 5.1, 5.1a

4.0D-G, 5.0, 5.0a

Tru64 Disk Space

NA

Not Available

1.2G Database 
3G Software 
1G Companion 
150M-1.9G Client

1.2G Database 
3G Software 
1G Companion 
150M-1.9G Client

4.5G

4.7G

1.5G

1.2G

811Mb

800Mb

800Mb

Tru64 RAM

NA

Not Available

1Gb 
256Mb (Client/Compan)

512Mb 
256Mb(Client/Compan)

512Mb

256Mb

128Mb

128Mb

128Mb

128Mb

128Mb

Tru64 swap

NA

Not Available

2Gb or match RAM 
512Mb(Client/Compan)

1Gb or match RAM 
512Mb(Client/Compan)

1Gb or match RAM

400Mb

400Mb

400Mb

2-4*RAM

2-4*RAM

2-4*RAM

Tru64 tmp

NA

Not Available

400Mb

400Mb

400Mb

400Mb

75Mb

?

75Mb

40Mb

40Mb

Tru64 JDK & JRE

NA

Not Available

SDK 1.4.2 needs to be installed 
download here

SDK 1.4.2 needs to be installed 
download here

JDK 1.3.1.03 & 1.1.8-10

JDK 1.2.2-8 & 1.1.8-10

JDK 1.2.2. & 1.1.8-7

1.1.8

?

n/a

n/a

Tru64 Patches/ 
Packages

NA

Not Available

OSFCMPLRS 
OSFLIBA 
OSFPGMR 
OSFSER 
OSFX11

5.1B-3 (patchkit 5): T64V51BB26AS0005-20050502

OSFSER 
OSFLIBA 
OSFPGMR 
OSFCMPLRS 
OSFX11 
OSFXDEVX (Spatial only) 
OSFXINCLUDE (Spatial only) 
OSFXLIBA (Spatial only)

5.1B-3 (patchkit 5): T64V51BB26AS0005-20050502

OSFSER 
OSFLIBA 
OSFPGMR 
OSFCMPLRS 
OSFX11

o 5.1a with patchkit 6 or higher required: 
T64V51AB24AS0006-20031031 
o HP Tru64 UNIX Performance improvement to times(3) system call: 
T64KIT0023583-V51AB24-E-20040913 
o HP Tru64 UNIX V5.1A PK6 (BL24) ERP Kit – file region locks can be inadvertently released as a result of AIO processing: 
T64KIT0023109-V51AB24-E-20040729

o 5.1B-3 (patchkit 5): T64V51BB26AS0005-20050502

OSFSER 
OSFLIBA 
OSFPGMR 
OSFCMPLRS 
OSFX11

5.0a 
patchkit 2 and bugfix HPAQ217F3 or 
patchkit 3 and bugfix HPAQ217F3 or 
patchkit 4

5.1 
patchkit 5 with T64V5117_C0038300
_unique_id_and_mfg_date.tar T64V51B19-C0125001-14319-E-20020516.tar (C1250.01 PatchId), T64V51B19-C0151600-15736-E-20021017.tar (C1516.00 PatchId).Go to here to download

5.1a 
patchkit 4 with T64V51AB3-C0074700-15747-E-20021018.tar (C747.00 PatchId). Go to hereto download

5.1b = Patchkit 2 or greater, apply patch 01414.00 (included in Pk3) to address Note 261309.1 ld seg fault = Patchkit 2 or greater

The following additional 5.1b O/S patch is also required, please obtain from HP: T64KIT0021686-V51BB24-E-20040223 — File Locking issue

OSFLIBA, 
OSFPGMR, 
OSFCMPLRS

4.0D = Patchkit 4 or greater

4.0E = Patchkit 2 or greater

4.0F = Patchkit 1 or greater

5.1 = Patchkit 5 or greater with T64V51B19-C0125001-14319-E-20020516.tar (C1250.01 PatchId) and T64V51B19-C0151600-15736-E-20021017.tar (C1516.00 PatchId). .Go to here to download

5.1a = Patchkit 3 or greater with T64V51AB3-C0074700-15747-E-20021018.tar (C747.00 PatchId). Go to here to download

5.1b = Patchkit 2 or greater, apply patch 01414.00 (included in Pk3) to addressNote 261309.1 ld seg fault

The following additional 5.1b O/S patch is also required, please obtain from HP: T64KIT0021686-V51BB24-E-20040223 — File Locking issue

OSFLIBA, 
OSFPGMR, 
OSFCMPLRS

4.0D = Patchkit 4 or greater

4.0E = Patchkit 2 or greater

4.0F = Patchkit 1 or greater

OSFLIBA, 
OSFPGMR, 
OSFCMPLRS

OSFLIBA, OSFPGMR, OSFCMPLRS

 

Tru64 Kernel Settings

NA

Not Available

PER_PROC_STACK_SIZE 838860833554432 to avoid ORA-4030s (Install Guide recommends 8388608) 
MAX_PER_PROC_STACK_SIZE 33554432
PER_PROC_DATA_SIZE 335544320 or RAM (whichever is greater) 
MAX_PER_PROC_DATA_SIZE 335544320 or RAM (whichever is greater) 
PER_PROC_ADDRESS_SPACE 1073741824 or RAM (whichever is greater) 
MAX_PER_PROC_ADDRESS_SPACE 1073741824 or RAM (whichever is greater) 
SHM_MAX 4278190080 (4 GB less 16MB) 
SHM_MIN 1 
SHM_MNI 256 
SHM_SEG 256 
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223) Note 272697.1 
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed 
NEW_WIRE_METHOD 0 (if <= 5.1b PK2) Note 272697.1 
VM_BIGPG_ENABLED 0 
FIFO_DO_ADAPTIVE 0 
SSM_THRESHOLD * 
MSG_SIZE 32768 
MAX_OBJS 5120 
MAX_ASYNC_REQ 256 
MAX_SESSIONS 500 
RDG_MAX_AUTO_MSG_WIRES 0 
RDG_AUTO_MSG_WIRES 0 
AIO_TASK_MAX_NUM 8193 
EXEC_DISABLE_ARG_LIMIT 1

* Set this attribute to 0 only if the rad_gh_regions[n] or gh_chunks attributes are set in the vm subsystem. Otherwise, do not change the value.

PER_PROC_STACK_SIZE 8388608 33554432 to avoid ORA-4030s (Install Guide recommends 8388608) 
MAX_PER_PROC_STACK_SIZE 33554432 
PER_PROC_DATA_SIZE 335544320 
MAX_PER_PROC_DATA_SIZE 335544320 
PER_PROC_ADDRESS_SPACE 1073741824 or RAM (whichever is greater) 
MAX_PER_PROC_ADDRESS_SPACE 1073741824 or RAM (whichever is greater)
SHM_MAX 4278190080 (4 GB less 16MB) 
SHM_MIN 1 
SHM_MNI 256 
SHM_SEG 256 
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223) Note 272697.1 
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed 
NEW_WIRE_METHOD 0 (if <= 5.1b PK2)Note 272697.1 
VM_BIGPG_ENABLED 0 
FIFO_DO_ADAPTIVE 0 
SSM_THRESHOLD * 
MSG_SIZE 32768 
MAX_OBJS 5120 
MAX_ASYNC_REQ 256 
MAX_SESSIONS 500 
RDG_MAX_AUTO_MSG_WIRES 0 
RDG_AUTO_MSG_WIRES 0 
AIO_TASK_MAX_NUM 8193

* Set this attribute to 0 only if the rad_gh_regions[n] or gh_chunks attributes are set in the vm subsystem. Otherwise, do not change the value.

MAX_PER_PROC_STACK_SIZE 33554432 
PER_PROC_STACK_SIZE 8388608 33554432 to avoid ORA-4030s (Install Guide recommends 8388608) 
PER_PROC_DATA_SIZE 201326592 
SHM_MAX 4278190080 (4 GB less 16MB) 
SHM_MIN 1 
SHM_MNI 256 
SHM_SEG 128 
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223 or 5.1a PK6) Note 272697.1 
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed 
NEW_WIRE_METHOD 0 (if <= 5.1b PK2)Note 272697.1 
VM_BIGPG_ENABLED 0 
FIFO_DO_ADAPTIVE 0

Alpha processor EV5.6 or later

PER_PROC_STACK_SIZE 33554432 
MAX_PER_PROC_STACK_SIZE 536870912 
PER_PROC_DATA_SIZE RAM 
MAX_PER_PROC_DATA_SIZE RAM 
PER_PROC_ADDRESS_SIZE RAM
MAX_PER_PROC_ADDRESS_SIZE RAM 
SHM_MAX 4278190080 (4 GB less 16MB) 
SHM_MIN 1 
SHM_MNI 256 
SHM_SEG 128 
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223) Note 272697.1 
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed 
NEW_WIRE_METHOD 0 (if <= 5.1b PK2) Note 272697.1 
FIFO_DO_ADAPTIVE 0

Alpha processor EV5.6 or later

SHMMAX 2139095040(2GB-8MB) 
SHMMIN 1 
SHMMNI 100 
SHMSEG 32 
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223) Note 272697.1 
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed 
NEW_WIRE_METHOD 0 (if <= 5.1b PK2)Note 272697.1 
FIFO_DO_ADAPTIVE 0

vm-mapentries=1024 in the /etc/sysconfigtab, verify with ‘/sbin/sysconfig -q vm’ – applies to OS versions below 5.0, starting in 5.0 it is autoset

Alpha processor EV5.6 or later

SHMMAX 2139095040(2GB-8MB) 
SHMMIN 1 
SHMMNI 100 
SHMSEG 32

SHMMAX 8388608 or higher than the maximum SGA size. 
Note: If anticipated SGA size is greater than 2 GB, set it to 2 GB – 8 MB; otherwise, round the SGA sizeup to the next 8 MB and set that to SHMMAX. 
SHMMIN 1 
SHMMNI 100 
SHMSEG 32

SHMMAX 
2139095040 (2 GB-8 MB) 
SHMMIN 1 
SHMMNI 100 
SHMSEG 32

SHMMAX 8388608 or higher than the maximum SGA size. 
Note: If anticipated SGA size is greater than 2 GB, set it to 2 GB – 8 MB; otherwise, round the SGA size up to the next 8 MB and set 
that to SHMMAX. 
SHMMIN 1 
SHMMNI 100 
SHMSEG 32

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

Linux x86 OS 
(See Note 225710.1 for supported kernels) andNote 265262.1for “Things to know about Linux”


o RHEL4,OEL4 – Update 7 or greater which is Kernel 2.6.9-78 or newer 
o RHEL5, OEL5 – 5.2 or greater which is Kernel 2.6.18-92 or newer 
o Red Hat Enterprise Linux 6 – Kernel 2.6.32-71 or later 
o SLES10 – Kernel 2.6.16.21 or higher
o SLES 11 – Kernel 2.6.27.19-5 or greater 
o Asianux Server 3 SP2 

NOTE: On RHEL6/OEL6, 11.2.0.3 or later is certified (not 11.2.0.1 or 11.2.0.2)


o RHEL4, OEL4, Asianux 2.0 
2.6.9 
o RHEL5, OEL5, Asianux Server 3 
2.6.18 
o SuSE SLES10 
2.6.16.21 
o SuSE SLES11 – Kernel 2.6.27.19-5 or greater

o RHEL 3 AS/ES ( RHEL3 ) (Update 4 or later) 
2.4.21-27.EL or higher 
o RHEL 4 AS/ES ( RHEL4 ) and Oracle Enterprise Linux 4 ( OEL4 ) 
2.6.9-5.0.5.EL or higher 
o RHEL 5 AS/ES ( RHEL5 ) and Oracle Enterprise Linux 5 ( OEL5 ) 
2.6.18-8 or higher 
o SuSE SLES9 
2.6.5-7.201 or higher 
o SuSE SLES10 
o SuSE SLES11 – Kernel 2.6.27.19-5 or greater 
o Asianux 1.0 
2.4.21-27.EL or higher 
o Asianux 2.0 
2.6.9-5.0.5.EL or higher

o RHEL AS/ES 2.1 (Update 3 or higher) 
2.4.9-e34 or higher 
o RHEL AS/ES 3.0 (Update 2 or higher) 
2.4.21-15.EL or higher 
o RHEL4 (10.1.0.3.0 patchset required) 
refer to 10.1.0.3.0 Release Notes 
o SuSE SLES8 (Service Pack 3 or higher) 
2.4.21-138 
o SuSE SLES9 
2.6.5-7.5 
o Red Flag Advanced Server 4.0 (China only) 
o Miracle Linux Std Ed 2.1 (Japan only) 
o Asianux 1.0

o Red Hat Enterprise AS/ES 2.1 
2.4.9-e34 or higher 
o Red Hat Enterprise AS/ES 3.0 
2.4.21-15 
o RHEL4 (9.2.0.6.0 patchset required or 9.2.0.5.0 patchset and Patch 4276910 required) 
refer to 9.2.0.4 Release Notes 
o SuSE SLES8 
2.4.21-138 
o SuSE SLES9 
2.6.5-7.97 
o United Linux 1.0 (SP3 or higher) 
o Red Flag DC Server 4.0 (China and Hong Kong only) 
o Monta Vista Carrier Grade Linux 3.0 (embedded) 
o Miracle Linux Std Ed 2.1 (Japan only) 
2.4.7 
o Asianux 1.0

Caldera OU8+LKP, Red Hat 7.1, Advanced Server 2.1, SuSE 7.1, 7.2, SLES7, Kernel 2.4.4

Caldera OU8+LKP, Miracle 1.0, 2.0, Red Hat 6.1,6.2, EE 6.2, 7.0, 7.1, Advanced Server 2.1, SuSE 7.0, 7.1, 7.2, SLES7, Kernel 2.2.16

Miracle 1.0, Red Hat 6.0,6.1,6.2, EE 6.2, SuSE 6.3, 6.4, 7.0, VA 6.2, Kernel 2.2

Red Hat 6.2, EE 6.2, SuSE 6.3, 6.4, Kernel 2.2

Red Hat 6.2, SuSE 6.4, 7.0, Kernel 2.0.34

2.0.34

Linux x86 Disk Space

3.8G Database

2G Database 
3.5G Install

1.2G Database 
1.5 to 3.5G Install

1.2G Database 
1.5G Software 
1G Companion 
150M-650M Client

4.5G

3.5G

900Mb

1G

811Mb

400Mb

400Mb

Linux x86 RAM

1GB

1GB

1GB

512Mb 
256Mb(Client/Compan)

512Mb

512Mb

128Mb

128Mb

128Mb

32Mb

32Mb

Linux x86 swap

If RAM=1 GB to 2 GB then 1.5 times RAM 
If RAM=2 GB to 16 GB then equal to RAM 
If greater than 16 GB then 16 GB

If RAM between 1 GB and 2 GB 
then 1.5 times RAM 
elseif RAM between 2 GB and 16 GB 
then match RAM 
else RAM > 16 GB 
then 16 GB

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

1Gb or match RAM 
512Mb(Client/Compan)

1Gb or match RAM

512Mb

400Mb

400Mb

256Mb

3*RAM

3*RAM

Linux x86 tmp

1024Mb

400Mb

400Mb

400Mb

400Mb

400Mb

75Mb

75Mb

75Mb

75Mb

20Mb

Linux x86 JDK & JRE

JDK (version TBS) is installed

JDK (version TBS) is installed

JDK 1.4.2_08 is installed

JDK 1.4.2_02 is installed

Sun JDK 1.3.1_02 & Blackdown 1.1.8_v3

Blackdown JDK 1.1.8_3 & 1.1.8_v3

JDK 1.2.2. & 1.1.8-3from IBM

1.1.8

1.1.6v5

n/a

n/a

Linux x86 Patches/ 
Packages

RHEL4, OEL4: 
Refer to Note 880211.1

 binutils-2.15.92.0.2-25

 compat-libstdc++-33-3.2.3-47.3

 elfutils-libelf-0.97.1-5

 glibc-2.3.4-2.41

 glibc-common-2.3.4-2.41

 libaio-0.3.105-2

 libgcc-3.4.6-10

 libstdc++-3.4.6-10

 make-3.80-7.EL4

 pdksh-5.2.14-30.6

 unixODBC-2.2.11-1.RHEL4.1

 The remaining Install Guide requirements will have to be installed:

 elfutils-libelf-devel-0.97.1-5.i386.rpm

 glibc-headers-2.3.4-2.41.i386.rpm

 glibc-kernheaders-2.4-9.1.103.EL.i386.rpm will be required as a prerequisite

 glibc-devel-2.3.4-2.41.i386.rpm

 gcc-3.4.6-10.i386.rpm

 libstdc++-devel-3.4.6-10.i386.rpm

 gcc-c++-3.4.6-10.i386.rpm

 libaio-devel-0.3.105-2.i386.rpm

 sysstat-5.0.5-19.el4.i386.rpm

 unixODBC-devel-2.2.11-1.RHEL4.1.i386.rpm

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

RHEL5, OEL5: 
Refer to Note 880936.1

RHEL6, OEL6: 
Refer to Oracle documentation

SLES10: 
Refer to Note 763386.1

SLES11: 
Refer to Note 881025.1

Asianux 2.0,OEL4,RHEL4: 
refer to Note 430653.1

 default Update 3 RPMs install or higher, see Note 376183.1

 binutils-2.15.92.0.2-18 *

 compat-libstdc++-33.2.3-47.3 *

 elfutils-libelf-0.97-5 *

 elfutils-libelf-devel-0.97-5

 glibc-2.3.4-2.19 *

 glibc-common-2.3.4-2.19 *

 glibc-devel-2.3.4-2.19

 glibc-headers-2.3.4-2.19 (glibc-devel required RPM)

 glibc-kernheaders-2.4-9.1.98 (glibc-devel required RPM)

 gcc-3.4.5-2

 gcc-c++-3.4.5-2

 libaio-0.3.105-2 *

 libaio-devel-0.3.105-2

 libgcc-3.4.5 *

 libstdc++-3.4.5-2 *

 libstdc++-devel-3.4.5-2

 make-3.80-5 *

 sysstat-5.0.5 *

 unixODBC-2.2.11-1.RHEL4

 unixODBC-devel-2.2.11-1.RHEL4 
* default OS installed

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

Asianux Server 3,OEL5,RHEL5: 
refer to Note 438765.1

 default RPM install, see Note 376183.1

 binutils-2.17.50.0.6-2.el5 *

 compat-libstdc++-33-3.2.3-61

 elfutils-libelf-0.125-3.el5 *

 elfutils-libelf-devel-0.125-3.el5

 elfutils-libelf-devel-static-0.125-3.el5 
(required by elfutils-libelf-devel)

 glibc-2.5-12 *

 glibc-common-2.5-12 *

 glibc-devel-2.5-12

 glibc-headers-2.5-12 
(required by glibc-devel)

 gcc-4.1.1-52.el5

 gcc-c++-4.1.1-52.el5

 libaio-0.3.106

 libaio-devel-0.3.106

 libgcc-4.1.1-52

 libgomp-4.1.1-52.el5 
(required by gcc)

 libstdc++-4.1.1-52.el5 *

 libstdc++-devel-4.1.1-52.el5

 make-3.81-1.1 *

 sysstat-7.0.0-3.el5

 unixODBC-2.2.11-7.1

 unixODBC-devel-2.2.11-7.1 
* default OS installed

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

SLES10: 
refer to Note 452818.1

 default RPM install, see Note 386391.1

 binutils-2.16.91.0.5-23.4 *

 compat-libstdc++-5.0.7-22.2 *

 glibc-2.4-31.2 *

 glibc-devel-2.4-31.2

 gcc-4.1.0-28.4

 gd-2.0.32-23.2 
(required by sysstat)

 gnuplot-4.0.0-20.2 
(requried by sysstat)

 ksh-93r-12.9 *

 libaio-0.3.104-14.2 *

 libaio-devel-0.3.104-14.2

 libelf-0.8.5-47.2

 libgcc-4.1.0-28.4 *

 libstdc++-4.1.0-28.4 *

 libstdc++-devel-4.1.0-28.4

 make-3.80-202.2 *

 plotutils-2.4.1-591.2 
(required by sysstat)

 sysstat-6.0.2-16.4

 unixODBC-2.2.11-21.4

 unixODBC-devel-2.2.11-21.4 
* default OS installed

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

SLES11: 
refer to Note 849583.1

RHEL3: default RPMS (see Note 376183.1)

 gcc-3.2.3-34

 glibc-2.3.2-95.20

 make-3.79.1

 openmotif21-2.1.30-8

 compat-db-4.0.14.5

 compat-gcc-7.3-2.96.128

 compat-gcc-c++-7.3-2.96.128

 compat-libstdc++-7.3-2.96.128

 compat-libstdc++-devel-7.3-2.96.128

 setarch-1.3-1

 XFree86 (Spatial only)

 XFree86-devel (Spatial only)

RHEL4: 
refer to Note 343431.1 default RPMS (see Note 376183.1)

 binutils-2.15.92.0.2-10.EL4

 compat-db-4.1.25-9

 compat-libstdc++-296-2.96-132.7.2

 compat-libstdc++-33-3.2.3-47.3

 control-center-2.8.0-12

 gcc-3.4.3-9.EL4

 gcc-c++-3.4.3-9.EL4

 glibc-2.3.4-2

 glibc-common-2.3.4-2

 gnome-libs-1.4.1.2.90-44.1

 libstdc++-3.4.3-9.EL4

 libstdc++-devel-3.4.3-9.EL4

 make-3.80-5

 pdksh-5.2.14-30

 sysstat-5.0.5-1

 xscreensaver-4.18-5.rhel4.2

 openmotif21-2.1.30-11.RHEL4.2 (required to install Oracle demos)

 libaio-0.3.102-1

[Red Hat,Oracle] Enterprise Linux 5.0 
Refer to Note 419646.1

 default RHEL5 RPMs (see Note 376183.1)

 default OEL5 RPMs (see Note 401167.1)

 gcc-c++-4.1.1-52.el5.i386.rpm and all its dependent packages. 
The dependent packages are: 
gcc-4.1.1-52.el5.i386.rpm 
libstdc++-devel-4.1.1-52.el5.i386.rpm 
glibc-devel-2.5-12.i386.rpm 
glibc-headers-2.5-12.i386.rpm 
libgomp-4.1.1-52.el5.i386.rpm

 libXp-1.0.0-8.i386.rpm

 compat-gcc-34-3.4.6-4.i386rpm

 compat-gcc-c++-34-3.4.6-4.i386rpm

 compat-libstdc++-33-3.2.3-61.i386.rpm

 sysstat-5.0.5-1.i386.rpm (OEL5 only)

SuSE SLES9: 
Refer to Note 400429.1

 default-RPMs (see NOTE 386391.1)

 glibc-devel-2.3.3-98.47.i586.rpm

 gcc-3.3.3-43.34.i586.rpm.

 libstdc++-devel-3.3.3-43.34.i586.rpm

 gcc-c++-3.3.3-43.34.i586.rpm

 db1-1.85-85.1.i586.rpm

 orbit-0.5.17-330.1.i586.rpm

 gnome-libs-1.4.1.7-671.1.i586.rpm.

 plotutils-2.4.1-575.1.i586.rpm

 gnuplot-3.7.3-256.1.i586.rpm

 sysstat-5.0.1-35.4.i586.rpm.

SLES10: 
refer to Note 387137.1

 default RPM install, see Note 386391.1

 glibc-devel-2.4-31.2.i586.rpm

 gcc-4.1.0-28.4.i586.rpm

 libstdc++-devel-4.1.0-28.4.i586.rpm

 gcc-c++-4.1.0-28.4.i586.rpm

 libaio-devel-0.3.104-14.2.i586.rpm

SLES11: 
refer to Note 842649.1

RHEL ES/AS 2.1:

 make-3.79

 gcc-2.96-128

 gcc-c++-2.96-128

 openmotif-2.1.30-11

 glibc-2.2.4-32

 libstdc++-2.96-128

 XFree86 (Spatial only)

 XFree86-devel (Spatial only)

RHEL ES/AS 3:
Refer to Note 394360.1

 default-RPMs (see NOTE 376183.1)

 gcc-3.2.3-34

 gcc-c++-3.2.3-34

 libstdc++-devel-3.2.3.3-34

 libaio-0.3.96-3.i386.rpm (required to configure Async IO)

 libaio-devel-0.3.96-3.i386.rpm (required to configure Async IO)

 XFree86 (Spatial only)

 XFree86-devel (Spatial only) 

set LD_ASSUME_KERNEL=2.4.19

RHEL4: 
Refer to Note 392940.1 
Patch 4153257 required for installer to work

 default RPMS (see Note 376183.1)

 binutils-2.15.92.0.2-10.EL4

 compat-db-4.1.25-9

 compat-libstdc++-296-2.96-132.7.2

 compat-libstdc++-33-3.2.3-47.3

 control-center-2.8.0-12

 gcc-3.4.3-9.EL4

 gcc-c++-3.4.3-9.EL4

 glibc-2.3.4-2

 glibc-common-2.3.4-2

 gnome-libs-1.4.1.2.90-44.1

 libstdc++-3.4.3-9.EL4

 libstdc++-devel-3.4.3-9.EL4

 make-3.80-5

 pdksh-5.2.14-30

 sysstat-5.0.5-1

 xscreensaver-4.18-5.rhel4.2

 openmotif21-2.1.30-11.RHEL4.2 (required to install Oracle demos)

 libaio-0.3.96

SuSE SLES8: 
Requires 10.1.0.3 Full Release (CD Release)

 make-3.79.1

 gcc-3.2.2-38

 gcc-c++-3.2.2-38

 glibc-2.2.2-124

 openmotif-2.2.2-124

 xf86 (Spatial only)

 xdevel (Spatial only)

SuSE SLES9: 
Requires 10.1.0.3 Full Release (CD Release)

 make-3.80

 gcc-3.3.3-43

 gcc-c++-3.3.3-43

 glibc-2.3.3-98

 libaio-0.3.98-18

 libaio-devel-0.3.98-18

 openmotif-libs-2.2.2-519.1

 xfree86 (Spatial only)

 xfree86-devel (Spatial only)

RHEL ES/AS 2.1:

 glibc 2.2.4-32

 make-3.79

 openmotif-2.1.30

 gcc-2.96-128

 gcc-c++-2.96-128

 libstdc++-2.96-128

RHEL ES/AS 3: 
Refer to Note 252217.1 default RPMS (seeNote 376183.1)

 glibc 2.3.2-95.20

 gcc-3.2.3-34

 make-3.79.1

 compat-db-4.0.14.5

 compat-gcc-7.3-2.96.128

 compat-gcc-c++-7.3-2.96.128

 compat-libstdc++-7.3-2.96.128

 compat-libstdc++-devel-7.3-2.96.128

 gnome-libs-1.4.1.2.90-34.1

 openmotif21-2.1.30-8

 setarch-1.3-1

To be able to install patch 3006854 these RPMs need to be installed

 glibc-devel-2.3.2-95.6.i386.rpm

 glibc-headers-2.3.2-95.20

 glibc-kernheaders-2.4-8.34 
Additional steps: 
Note 252217.1 for additional setup requirements for RHEL3 and 9.2 x86 
for Async I/O functionality to work you need to install Patch 3016968 on top of 9.2.0.3.0 or 9.2.0.4.0 or Patch 3208258 on top of 9.2.0.5.0 or 9.2.0.6.0

RHEL4: 
Refer to Note 303859.1 default RPMS (seeNote 376183.1)

 compat-db-4.1.25-9

 compat-gcc-32-3.2.3-47.3

 compat-gcc-32-c++-3.2.3-47.3

 compat-oracle-rhel4-1.0-3 (obtain Patch 4198954)

 compat-libcwait-2.0-1 (obtain Patch 4198954)

 compat-libgcc-296-2.96-132.7.2

 compat-libstdc++-296-2.96-132.7.2

 compat-libstdc++-33-3.2.3-47.3

 gcc-3.4.3-9.EL4

 gcc-c++-3.4.3-9.EL4

 gnome-libs-1.4.1.2.90-44

 gnome-libs-devel-1.4.1.2.90-44

 libaio-devel-0.3.102-1

 libaio-0.3.102-1

 make-3.80-5

 openmotif21-2.1.30-11

 xorg-x11-deprecated-libs-devel-6.8.1-23.EL

 xorg-x11-deprecated-libs-6.8.1-23.EL 
Patch 4188455 required for installer to work
Set LD_ASSUME_KERNEL=2.4.19 
Post install you need to apply Patch 4190568 on top of the 9.2.0.6 patchset 
Note 303859.1 for more specific steps for 9.2.0.6 on RHEL4

SuSE SLES8:

 gcc-3.2.2-38

 glibc-2.2.2-124

 make-3.79.1

 openmotif-2.2.2-124

SuSE SLES9: 
Refer to Note 427976.1 default RPMS (seeNote 386391.1)

 glibc-2.3.3

 gcc-3.3.3

 gcc-c++-3.3.3

 libaio-0.3.98

 libaio-devel-0.3.98

 make-3.80

 openmotif-libs-2.2.2-519.1

 orarun-1.8-109 
Additional steps for SLES9 for 9.2 32bit x86: 
Install 9.2.0.4 (Complete release) and then apply 9.2.0.5 and 9.2.0.5 one-off Patch 3809563 or 9.2.0.6 patchset 

If using Bourne, Bash, or Korn shell: ( /usr/lib/libInternalSymbols.so can be obtained from the orarun package ) 
ORACLE_BASE= ; export ORACLE_BASE 
LD_ASSUME_KERNEL=2.4.21; export LD_ASSUME_KERNEL 
LD_PRELOAD=/usr/lib/libInternalSymbols.so ; export LD_PRELOAD 
for Async I/O functionality to work you need to install Patch 3208258 on top of 9.2.0.5.0 or 9.2.0.6.0

make-3.79, and binutils-2.10.

GLIBC package version 2.1.3 or higher

GLIBC package version 2.1

GNU C Library, version 2.0.6 
GLIBC package version 2.1

GNU C Library, version 2.0.7 
TCL library (libtcl.so), version 8.0.2-16

GNU C Library, version 2.0.7 
TCL library (libtcl.so), version 8.0.2-16

Linux x86 Kernel Settings


kernel.shmmni = 4096 
kernel.sem = 250 32000 100 128 
fs.file-max = 6815744 512 x processes (for example 6815744 for 13312 processes) 
net.ipv4.ip_local_port_range = 9000 65500 
net.core.rmem_default = 262144 
net.core.rmem_max = 4194304 
net.core.wmem_default = 262144 
net.core.wmem_max = 1048576


SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SHMMAX RAM times 0.5 Note 567506.1
SHMMNI 4096 
SHMALL = SHMMAX/pagesize 
FILE-MAX =6815744 512* Processes 
IP_LOCAL_PORT_RANGE 9000 65500 
RMEM_DEFAULT 262144 
RMEM_MAX 4194304 
WMEM_DEFAULT 262144 
WMEM_MAX 2621441048576 
NET.IPV4.TCP_RMEM 4194304 4194304 4194304 
NET.IPV4.TCP_WMEM 262144 262144 262144

SuSE SLES9: 
SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SHMMAX RAM times 0.5 (Note 567506.1
SHMMNI 4096 
SHMALL = SHMMAX/pagesize 
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500 
RMEM_DEFAULT 262144 
RMEM_MAX 2097152 
WMEM_DEFAULT 262144 
WMEM_MAX 262144 
NET.IPV4.TCP_RMEM 1048576 1048576 1048576 
NET.IPV4.TCP_WMEM 262144 262144 262144

Other Linux OS: 
SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SHMMAX RAM times 0.5 (Note 567506.1
SHMMNI 4096 
SHMALL = SHMMAX/pagesize 
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500 
RMEM_DEFAULT 262144 
RMEM_MAX 2097152 
WMEM_DEFAULT 262144 
WMEM_MAX 262144 
NET.IPV4.TCP_RMEM 1048576 1048576 1048576 
NET.IPV4.TCP_WMEM 262144 262144 262144

SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SEMVMX 32767 
SHMMAX 2147483648 
One-half the size of your system’s physical memory. Check your system for additional restrictions. 
SHMMNI 4096 
SHMALL = SHMMAX/pagesize 
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500

SEMMNI 100 
SEMMNS 256 
SEMMSL 100 
SEMOPM 100 
SEMVMX 32767 
SHMMAX 2147483648 
One-half the size of your system’s physical memory. Check your system for additional restrictions. 
SHMMIN 1 
SHMMNI 4096 
SHMSEG 4096

SEMMNI 100 
SEMMNS 256 
SEMMSL 100 
SEMOPM 100 
SEMVMX 32767 
SHMMAX 2147483648 
One-half the size of your system’s physical memory. Check your system for additional restrictions. 
SHMMIN 1 
SHMMNI 4096 
SHMSEG 4096

SHMMAX 0.5*(physical memory present in machine) but not greater then 4Gb 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 100 
SEMMSL Set to 10 plus the largest PROCESSES parameter of any Oracle database on the system. 
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database, adding the largest one twice, then add an additional 10 for each database. 
SEMOPM 100 
SEMVMX 32767

SHMMAX 0.5*(physical memory present in machine) but not greater then 4Gb 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 100 
SEMMSL Set to 10 plus the largest PROCESSES parameter of any Oracle database on the system. 
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database, adding the largest one twice, then add an additional 10 for each database. 
SEMOPM 100 
SEMVMX 32767

SHMMAX 0.5 *(physical memory present in machine) but not greater then 4Gb 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNI 100 
SEMMSL Set to 10 plus the largest initsid.ora PROCESSES parameter of an Oracle database on the system. 
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database except the largest one, plus 2 times the largest PROCESSES value, plus 10 times the number of Oracle databases. 
SEMOPM 100 
SEMVMX 32767

SHMMAX (1/4 of RAM) but not greater then 4Gb 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNS 200 
SEMMNI 70 
SEMMSL Equal to or greater than the value of the 
PROCESSES initialization parameter.

SHMMAX (1/4 of RAM) but not greater then 4Gb 
SHMMIN 1 
SHMMNI 100 
SHMSEG 10 
SEMMNS 200 
SEMMNI 70 
SEMMSL Equal to or greater thanthe value of the 
PROCESSES initialization parameter.

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

Linux x86_64 EM64T AMD64 OS 
(See Note 225710.1 for supported kernels) andNote 265262.1for “Things to know about Linux”

o RHEL4,OEL4 – update 7 or greater 
o RHEL5,OEL5 – 5.2 or greater 
o RHEL6,OEL6 – 6.0 or greater 
o SLES10 – Kernel 2.6.16.21-0.8 or greater 
o SLES11 – Kernel 2.6.27.19-5 or greater 
o Asianux Server 3 SP2 

NOTE: On RHEL6/OEL6, 11.2.0.3 or later is certified (not 11.2.0.1 or 11.2.0.2) 

Refer Note 1304727.1 for certification information 

Refer 11.2 DB Installation Guide for Linux for Kernel requirement

 Asianux 2.0, [Red Hat,Oracle] Enterprise Linux 4.0: 
2.6.9

 Asianux Server 3, [Red Hat,Oracle] Enterprise Linux 5.0: 
2.6.18

 SUSE Linux Enterprise Server 10: 
2.6.16.21

 SuSE Linux Enterprise Server 11: 
2.6.27.19-5 or greater

o Red Hat Enterprise Linux ( RHEL 3 ) AS/ES (Update 4 or later) 
2.4.21-27.EL 
o RHEL4 AS/ES (Update 1 or later) or OEL4 
2.6.9-11.EL 
o RHEL5 AS/ES or OEL5 
2.6.18-8 or higher 
o SUSE Linux Enterprise Server 9.0 (SLES9) with SP2 or later 
2.6.5-7.201 
o SuSE Linux Enterprise Server 10 (SLES10) 
2.6.16.21-0.8 (or later) 
o SuSE Linux Enterprise Server 11 (SLES11) 
2.6.27.19-5 or greater 
o Asianux 2.0

o Red Hat Enterprise AS/ES 3.0 (Update 2 or higher) 
2.4.21-15.EL 
o Red Hat Enterprise AS/ES 4.0 (Update 1 or higher) 
2.6.9-11.EL smp 
o SuSE SLES8 (Service Pack 3 or higher) 
2.4.21-185-smp 
o SuSE SLES9 
2.6.5-7.97 
o Asianux 1.0 
requires 10.1.0.3

o Red Hat Enterprise AS/ES 3.0 
2.4.21-9 
o Red Hat Enterprise AS/ES 4.0 
minimum patchset level is 9.2.0.7.0 
o SuSE SLES8 
2.4.21-185 
o SuSE SLES9 
9.2.0.6 Required – needed for EM64T patch 4261532 & patch 4233179

           

Linux x86_64 EM64T AMD64 Disk Space

3.8Gb Database

1.68G Database 
3.8G to 4.4G Software

1.2G Database 
1.5 to 3.5G Install

1.2G Database 
1.5G Software 
1G Companion 
150M-650M Client

4.5G

           

Linux x86_64 EM64T AMD64 RAM

Database: minimum 1GB, recommended 2GB

Grid Infrastructure for standalone server: minimum 1.5GB (plus another 1GB if installing Database too), recommended 4GB

1GB

1GB

512Mb 
256Mb(Client/Compan)

512Mb

           

Linux x86_64 EM64T AMD64 swap

11.2 DB Installation Guide for Linuxsays: 
If RAM between 1 GB and 2 GB then 1.5 times the size fo RAM. 
If RAM between 2 GB to 16 GB then equal to the size of RAM. 
If RAM greater than 16 GB then 16 GB.

11.2 Grid Infrastructure (GI) Installation Guide for Linux says: 
If RAM between 2 GB and 8 GB then 2 times the size fo RAM. 
If RAM between 8 GB to 32 GB then 1.5 times the size of RAM. 
If RAM greater than 32 GB then 32 GB.

If RAM 1 GB and 2 GB 
then 1.5 times the size fo RAM. 
If RAM 2 GB to 16 GB 
then equal to the size fo RAM. 
If RAM greater than 16 GB 
then 16 GB

Automatic Memory Management 
Starting with Oracle Database 11g, the Automatic Memory Management feature requires more shared memory (/dev/shm) and file descriptors. The shared memory should be sized to be at least the greater of MEMORY_MAX_TARGET and MEMORY_TARGET for each Oracle instance on the computer. To determine the amount of shared memory available, enter the following command: # df -k /dev/shm/

Note: MEMORY_MAX_TARGET and MEMORY_TARGET cannot be used when LOCK_SGA is enabled or with huge pages on Linux

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

1Gb or match RAM 
512Mb(Client/Compan)

1Gb or match RAM

           

Linux x86_64 EM64T AMD64 tmp

1024Mb

400Mb

400Mb

400Mb

400Mb

           

Linux x86_64 EM64T AMD64 JDK & JRE

You can use Sun JDK 1.5.0-06 with the JNDI extension JDK versions with the Oracle Java Database Connectivity and Oracle Call Interface drivers. 
However, these are not mandatory for the installation

You can use Sun JDK 1.5.0-06 with the JNDI extension JDK versions with the Oracle Java Database Connectivity and Oracle Call Interface drivers. 
However, these are not mandatory for the installation

JDK 1.4.2_08 is installed

JDK 1.4.2_02 is installed

o Sun JDK 1.4.2_03 is installed

           

Linux x86_64 EM64T AMD64 Patches/ 
Packages

RHEL6,OEL6: 
Refer to Note 1441282.1 

RHEL5,OEL5: 
Refer to Note 880989.1 
binutils-2.17.50.0.6-6.el5 (x86_64) 
compat-libstdc++-33-3.2.3-61 (x86_64) << both ARCH’s are required. See next line. 
compat-libstdc++-33-3.2.3-61 (i386) << both ARCH’s are required. See previous line. 
elfutils-libelf-0.125-3.el5 (x86_64) 
glibc-2.5-24 (x86_64) << both ARCH’s are required. See next line. 
glibc-2.5-24 (i686) << both ARCH’s are required. See previous line. 
glibc-common-2.5-24 (x86_64) 
ksh-20060214-1.7 (x86_64) 
libaio-0.3.106-3.2 (x86_64) << both ARCH’s are required. See next line. 
libaio-0.3.106-3.2 (i386) << both ARCH’s are required. See previous line. 
libgcc-4.1.2-42.el5 (i386) << both ARCH’s are required. See next line. 
libgcc-4.1.2-42.el5 (x86_64) << both ARCH’s are required. See previous line. 
libstdc++-4.1.2-42.el5 (x86_64) << both ARCH’s are required. See next line. 
libstdc++-4.1.2-42.el5 (i386) << both ARCH’s are required. See previous line. 
make-3.81-3.el5 (x86_64) 
The remaining Install Guide requirements will have to be installed: 
elfutils-libelf-devel-0.125-3 (x86_64) 
a.) requires elfutils-libelf-devel-static-0.125-3 (x86_64) as a prerequisite, as listed below. 
b.) elfutils-libelf-devel and elfutils-libelf-devel-static each depend upon the other. Therefore, they must be installed together, in one (1) “rpm -ivh” command as follows: 
rpm -ivh elfutils-libelf-devel-0.125-3.el5.x86_64.rpm elfutils-libelf-devel-static-0.125-3.el5.x86_64.rpm 
glibc-headers-2.5-24 (x86_64) 
a.) requires kernel-headers-2.6.18-92 (x86_64) as a prerequisite, as listed below 
glibc-devel-2.5-24 (x86_64) << both ARCH’s are required. See next item. 
glibc-devel-2.5-24 (i386) << both ARCH’s are required. See previous item. 
gcc-4.1.2-42.el5 (x86_64) 
a.) requires libgomp-4.1.2-42 (x86_64) as a prerequisite, as listed below 
libstdc++-devel-4.1.2-42 (x86_64) 
gcc-c++-4.1.2-42.el5 (x86_64) 
libaio-devel-0.3.106-3.2 (x86_64) << both ARCH’s are required. See next item 
libaio-devel-0.3.106-3.2 (i386) << both ARCH’s are required. See previous item. 
sysstat-7.0.2-1 (x86_64) 
unixODBC-2.2.12 (x86_64) << both ARCH’s are required. See next item and Note:762206.1 
unixODBC-2.2.12 (i386) << both ARCH’s are required. See previous item and Note:762206.1 
unixODBC-devel-2.2.12 (x86_64) << both ARCH’s are required. See next item and Note:762206.1 
unixODBC-devel-2.2.12 (i386) << both ARCH’s are required. See previous item and Note:762206.1

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

RHEL4,OEL4: 
Refer to Note 880942.1

SLES10:- 
Refer to Note 884435.1

SLES11 :- 
Refer to Note 881044.1

Asianux 2.0 
[Oracle, Red Hat] Enterprise Linux 4.0 
(See Note 437123.1):

 default RPMs (see Note 376183.1)

 binutils-2.15.92.0.2

 compat-libstdc++-33-3.2.3

 compat-libstdc++-33-3.2.3 (32 bit)

 elfutils-libelf-0.97

 elfutils-libelf-devel-0.97

 gcc-3.4.5

 gcc-c++-3.4.5

 glibc-2.3.4-2.19

 glibc-2.3.4-2.19 (32 bit)

 glibc-common-2.3.4

 glibc-devel-2.3.4

 glibc-devel-2.3.4 (32-bit)

 libaio-0.3.105

 libaio-0.3.105 (32 bit)

 libaio-devel-0.3.105

 libgcc-3.4.5

 libgcc-3.4.5 (32-bit)

 libstdc++-3.4.5

 libstdc++-3.4.5 (32 bit)

 libstdc++-devel 3.4.5

 make-3.80

 sysstat-5.0.5

Asianux Server 3 
[Oracle, Red Hat] Enterprise Linux 5.0 
(see Note 438766.1):

 default RHEL5 RPMs (see Note 376183.1)

 default OEL5 RPMs (see Note 401167.1)

 binutils-2.17.50.0.6

 compat-libstdc++-33-3.2.3

 compat-libstdc++-33-3.2.3 (32 bit)

 elfutils-libelf-0.125

 elfutils-libelf-devel-0.125

 gcc-4.1.1

 gcc-c++-4.1.1

 glibc-2.5-12

 glibc-2.5-12 (32 bit)

 glibc-common-2.5

 glibc-devel-2.5

 glibc-devel-2.5-12 (32 bit)

 libaio-0.3.106

 libaio-0.3.106 (32 bit)

 libaio-devel-0.3.106

 libgcc-4.1.1

 libgcc-4.1.1 (32 bit)

 libstdc++-4.1.1

 libstdc++-4.1.1 (32 bit)

 libstdc++-devel 4.1.1

 make-3.81

 sysstat-7.0.0

SuSE SLES 10 
(see Note 457143.1):

 default-RPMs (see NOTE 386391.1)

 binutils-2.16.91.0.5

 compat-libstdc++-5.0.7-22.2

 gcc-4.1.0

 gcc-c++-4.1.0

 glibc-2.4-31.2

 glibc-32bit-2.4-31.2 (32 bit)

 glibc-devel-2.4

 glibc-devel-32bit-2.4 (32 bit)

 libaio-0.3.104

 libaio-32bit-0.3.104 (32 bit)

 libaio-devel-0.3.104

 libelf-0.8.5

 libgcc-4.1.0

 libstdc++-4.1.0

 libstdc++-devel-4.1.0

 make-3.80

 sysstat-6.0.2

Note: If you did not perform a default Linux installation, you intend to use LDAP, and you want to use the scripts odisrvreg, oidca, or schemasync, then install the Korn shell RPM for your Linux distribution.

SuSE SLES 11 
(see Note 1081555.1)

Red Hat Enterprise Linux 3.0: 
Refer to Note 353735.1

 default RPMs (see Note 376183.1)

 compat-db 4.0.14-5.1

 compat-gcc-7.3-2.96.128 (32 bit)

 compat-gcc-c++-7.3-2.96.128 (32 bit)

 compat-libstdc++-7.3-2.96.128 (32 bit)

 compat-libstdc++-devel-7.3-2.96.128 (32 bit)

 control-center-2.2.0.1-13

 gcc-3.2.3-47

 gcc-c++-3.2.3-47

 gdb-6.1post-1.20040607.52

 glibc-2.3.2-95.30

 glibc-common-2.3.2-95.30

 glibc-devel-2.3.2-95.30

 glibc-devel-2.3.2-95.20 (32 bit)

 gnome-libs-1.4.1.2.90-34.2 (32 bit)

 libaio-0.3.96-3

 libaio-devel-0.3.96-3

 libstdc++-3.2.3-47

 libstdc++-devel-3.2.3-47

 make-3.79.1-17

 openmotif-2.2.3-3.RHEL3

 sysstat-5.0.5-5.rhel3

 setarch-1.3-1

[Red Hat,Oracle] Enterprise Linux 4.0: 
Refer to Note 339510.1

 default RPMs (see Note 376183.1)

 binutils-2.15.92.0.2-13.0.0.0.2.x86_64Download here or you can install binutils-2.15.92.0.2-18.x86_64.rpm from RHEL4 Update 3.

 compat-db-4.1.25-9.x86_64.rpm

 compat-gcc-32-c++ )see Note 430526.1
Patch 5240469 to correct bad genoccish file

 compat-libstdc++-33-3.2.3-47.3.x86_64.rpm

 compat-libstdc++-33-3.2.3-47.3.i386.rpm

 control-center-2.8.0-12.x86_64.rpm

 gcc-3.4.3-47.x86_64.rpm

 gcc-c++-3.4.3-47.x86_64.rpm

 glibc-2.3.4-2.9.x86_64.rpm

 glibc-2.3.4-2.9.i386.rpm

 glibc-common-2.3.4-2.9.x86_64.rpm

 glibc-devel-2.3.4-2.9.x86_64.rpm

 glibc-devel-2.3.4-2.9.i386.rpm

 glibc-headers-2.3.4-2.9.x86_64.rpm

 glibc-kernheaders-2.4-9.1.87.x86_64.rpm

 gnome-libs-1.4.1.2.90-44.1.x86_64

 libaio-0.3.103-3.i386.rpm

 libaio-0.3.103-3.x86_64.rpm

 libgcc-3.4.3-9.EL4

 libstdc++-3.4.3-22.1.x86_64

 libstdc++-devel-3.4.3-22.1.x86_64

 make-3.80-5.x86_64.rpm

 pdksh-5.2.14-30.x86_64.rpm

 sysstat-5.0.5-1.x86_64.rpm

 util-linux-2.12a-16.EL4.23.x86_64 (for raw devices)

 xorg-x11-deprecated-libs-6.8.1-23

 xscreensaver-4.18-5.rhel4.2.x86_64.rpm

[Red Hat,Oracle] Enterprise Linux 5.0 
Refer to Note 421308.1 
Since RHEL5/OEL5 are not recognized by runInstaller do: 
./runinstaller -ignoreSysPrereqs

 default RHEL5 RPMs (see Note 376183.1)

 default OEL5 RPMs (see Note 401167.1)

 compat-gcc-34-3.4.6-4

 compat-gcc-34-c++-3.4.6-4

 compat-libstdc++-33-3.2.3-61.i386.rpm

 compat-libstdc++-33-3.2.3-61.x86_64.rpm

 gcc-c++-4.1.1-52.el5.x86_64.rpm and all its dependent packages. 
The dependent packages are: 
libstdc++-devel-4.1.1-52.el5.x86_64.rpm
glibc-headers-2.5-12.x86_64.rpm 
glibc-devel-2.5-12.i386.rpm 
glibc-devel-2.5-12.x86_64.rpm 
libgomp-4.1.1-52.el5.x86_64.rpm 
gcc-4.1.1-52.el5.x86_64.rpm

 libXp-1.0.0-8.i386.rpm

 sysstat-7.0.0-3.el5.x86_64.rpm

 util-linux-2.13-0.44.el5.x86_64 (for raw devices)

SUSE Linux Enterprise Server 9: 
Refer to Note 365607.1

 default-RPMs (see NOTE 386391.1)

 binutils-2.15.90.0.1.1-32.5

 db1-1.85-85.1

 gcc-3.3.3-43.24

 gcc-c++-3.3.3-43.24

 glibc-2.3.3-98.28

 glibc-32bit-9-200506071326

 glibc-devel-2.3.3-98-47

 glibc-devel-32bit-9-200506062332

 libaio-0.3.102.1.2

 libaio-devel-0.3.102.1.2

 gnome-libs-1.4.1.7-671.1

 gnuplot-3.7.3-256.1 (sysstat required RPM)

 libstdc++-3.3.3-43.24

 libstdc++-devel-3.3.3-43.24

 make-3.80-184.1

 orbit-0.5.17-330.1 (gnome-libs required RPM)

 plotutils-2.4.1-575.1 (sysstat required RPM)

 pdksh-5.2.14-780.1

 sysstat-5.0.1-35.1

 XFree86-libs-4.3.99.902.43.48

SUSE Linux Enterprise Server 10: 
Refer to Note 373681.1 
Since SLES10 is not recognized by runInstaller do: 
./runinstaller -ignoreSysPrereqs

 default-RPMs (see NOTE 386391.1)

 glibc-devel-2.4-31.2.x86_64.rpm

 gcc-4.1.0-28.4.x86_64.rpm

 libstdc++-devel-4.1.0-28.4.x86_64.rpm

 gcc-c++-4.1.0-28.4.x86_64.rpm

 glibc-devel-32bit-2.4-31.2.x86_64.rpm

 libaio-devel-0.3.104-14.2.x86_64.rpm 

SuSE Linux Enterprise Server 10 special instructions: 1. Execute runInstaller with the -ignoreSysPrereqs option.

SUSE Linux Enterprise Server 11: 
Refer to Note:956194.1 for a list of required SLES11 packages 
Since SLES11 is not recognized by runInstaller do: 
./runinstaller -ignoreSysPrereqs

RHEL 3 (Update 2): 
Refer to Note 351679.1

 default-RPMs (see NOTE 376183.1)

 make-3.79.1

 gcc-3.2.3-34

 glibc-2.3.2-95.20

 glibc-devel-2.3.2-95.20

 glibc-devel-2.3.2-95.20 (32 bit)

 compat-db-4.0.14-5

 compat-gcc-7.3-2.96.128 (32 bit)

 compat-gcc-c++-7.3-2.96.128 (32 bit)

 compat-libstdc++-7.3-2.96.128 (32 bit)

 compat-libstdc++-devel-7.3-2.96.128 (32 bit)

 gnome-libs-1.4.1.2.90-34.1 (32 bit)

 openmotif21-2.1.30-8 (32 bit)

 setarch-1.3-1

 libaio-0.3.96-3

 libaio-devel-0.3.96-3

 XFree86-libs-4.3.0-62 (32bit)

RHEL 4: 
Refer to Note 390900.1 Requires My Oracle Support (MOS) patch5201236Bug 4387087

 default-RPMs (see NOTE 376183.1)

 glibc-kernheaders-2.4-9.1.87 (x86_64)

 glibc-headers-2.3.4-2.9 (x86_64)

 glibc-devel-2.3.4-2.9 (x86_64)

 glibc-devel-2.3.4-2.9 (i386)

 libstdc++-devel-3.4.3-22.1 (x86_64)

 gcc-3.4.3-22.1 (x86_64)

 gcc-c++-3.4.3-22.1 (x86_64)

 sysstat-5.0.5-1 (x86_64)
 

Note: 
openmotif21-2.1.30-11.RHEL4.2 is required to install Oracle demos. 
GNU Compiler Collection (GCC) 2.96 is not supported on Red Hat Enterprise Linux 4.0. 
Gcc 3.2.3 is required for OCCI application

SuSE SLES8 (Service Pack 3 or later):

 make-3.79.1

 gcc-3.3.3-43

 gcc-c++-3.3.3-43

 glibc-2.2.5-213

 glibc-32bit-8.1-9

 glibc-devel-32bit-8.1-9

 openmotif-2.2.2-124

 libaio-0.3.96-3

 libaio-devel-0.3.96-3

SuSE SLES9:

 gcc-3.3.3-43

 gcc-c++-3.3.3-43

 glibc-2.3.3-98

 glibc-32bit-9 (Bug 4405422)

 glibc-devel-32bit-9 (Bug 4405422)

 libaio-0.3.98-18

 libaio-devel-0.3.98-18

 make-3.80

 openmotif-libs-2.2.2-519.1

RHEL ES/AS 3 
Please refer to Note: 308588.1LD_ASSUME_KERNEL=2.4.19

 glibc 2.3.2-95.x86_64

 gcc-3.2.3-24.x86_64

 gcc-c++-3.2.3-24.x86_64

 libstdc++-3.2.3-24.i386

 libstdc++-devel-3.2.3-24.x86_64

 libstdc++-3.2.3-24.x86_64

 glibc-devel-2.3.2-95.3.i386 (Foot 1)

 glibc-2.3.2-95.6.i686

 make 3.79.1.x86_64

 gnome-libs-1.4.1.2.90-34.1.i386 (Foot 2)

 ORBit-0.5.17-10.4.i386

 audiofile-0.2.3-7.1.i386

 esound-0.2.28-5.1.i386

 gtk+-1.2.10-27.1.i386

 imlib-1.9.13-12.i386

 libpng10-1.0.13-8.i386

 libungif-4.1.0-15.i386

 tcp_wrappers-7.6-34.i386

 setarch-1.3-1.x86_64

 libaio-0.3.96-3.x86_64 
Note:The x86_64 rpms are on the RHEL 3 x86_64 distribution. The i386 rpms are on the RHEL 3 x86 distribution.

o Footnote 1 
This package might require the –force option during installation. 
o Footnote 2 
This package might require the –force option during installation if 64-bit gnome packages are installed. Oracle recommends that you do not install 64-bit gnome packages if they are not required for other applications.

RHEL ES/AS 4

Please refer to Note: 353529.1

 a “default-RPMs” installation of RHEL AS/ES 4 update 1. Additional RPMs may be needed if a “less-than-default-RPMs” installation of RHEL AS/ES 4 update 1 is performed.

 compat-gcc-32-3.2.3-47.3.x86_64.rpm

 compat-gcc-32-c++-3.2.3-47.3.x86_64.rpm

 glibc-kernheaders-2.4-9.1.87.x86_64.rpm

 glibc-headers-2.3.4-2.9.x86_64.rpm

 glibc-devel-2.3.4-2.9.x86_64.rpm

 libstdc++-devel-3.4.3-22.1.x86_64.rpm

 glibc-devel-2.3.4-2.9.i386.rpm

 libaio-0.3.103-3.x86_64.rpm

 ORBit-0.5.17-14.i386.rpm

 gnome-libs-1.4.1.2.90-44.1.i386.rpm 
The x86_64 packages are on the Red Hat Enterprise Linux 4 x86-64 distribution. 
The i386 packages are also on the Red Hat Enterprise Linux 4 x86-64 distribution.

SuSE SLES8 (Service Pack 3 or higher)

 glibc-2.2.5-213.x86_64

 glibc-32bit-8.1-9.i586

 glibc-devel-32bit-8.1-9.i586

 gcc-33-3.3-43.x86_64

 gcc-33-c++3.3-43.x86_64

 libstdc++-33-3.3-43.x86_64

 libstdc++-devel-33-3.3-43.x86_64

 make-3.79.1-42.x86_64

 libaio-0.3.15-138.x86_64 (This version of libaio is required for asynchronous I/O.) 
Note: Create a symbolic link such that /usr/bin/gcc points to /opt/gcc33/bin/gcc. Otherwise the installation fails with relinking errors.

SuSE SLES9 
Please refer to Note: 361169.1 
Set LD_ASSUME_KERNEL=2.4.20

 compat-2004.7.1-1.2

 compat-32bit-9-200407011229

 XFree86-libs-4.3.99.902-43.22

 XFree86-libs-32bit-9-200407011229

 libaio-devel-0.3.98-18.4

 libaio-32bit-9-200407011229

 libaio-0.3.98-18.4

 libaio-devel-32bit-9-200407011229

 glibc-32bit-9-200506071326

 glibc-devel-32bit-9-200506071326 orarun-1.8-31

           

Linux x86_64 EM64T AMD64 Kernel Settings

kernel.shmmni = 4096 
kernel.sem = 250 32000 100 128 
fs.file-max = 6815744 512 x processes (for example 6815744 for 13312 processes_ 
net.ipv4.ip_local_port_range = 9000 65500 
net.core.rmem_default = 262144 
net.core.rmem_max = 4194304 
net.core.wmem_default = 262144 
net.core.wmem_max = 1048576 
kernel.shmall = physical RAM size / pagesize For most systems, this will be the value 2097152. See Note: 301830.1 for more information. 
kernel.shmmax = RAM times 0.5 (or higher at customer’s discretion – seeNote:567506.1
kernel.shmmni = 4096 
kernel.sem = 250 32000 100 128 
aio-max-nr=1048576

SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SHMMAX RAM times 0.5 (Note 567506.1
SHMMNI 4096 
SHMALL = SHMMAX/pagesize (Note:301830.1
FILE-MAX 6815744 512 * Processes 
IP_LOCAL_PORT_RANGE 9000 65500 
RMEM_DEFAULT 262144 
RMEM_MAX 4194304 
WMEM_DEFAULT 262144 
WMEM_MAX 262144 1048576 
NET.IPV4.TCP_RMEM (RMEM_DEFAULT) (RMEM_DEFAULT) (RMEM_MAX) 
NET.IPV4.TCP_WMEM (WMEM_DEFAULT) (WMEM_DEFAULT) (WMEM_MAX)

To increase the shell limits: 
1. Add the following lines in the /etc/security/limits.conf file: 
oracle soft nproc 2047 
oracle hard nproc 16384 
oracle soft nofile 1024 
oracle hard nofile 65536 
2. Add the following line to the /etc/pam.d/login file, if it does not already exist: 
session required /lib/security/pam_limits.so 
session required pam_limits.so Note 437123.1 
Lines from the Fix section of Note 301665.1 
3. Depending on the oracle user’s default shell, make the following changes to the default shell startup file: 
For the Bourne, Bash, or Korn shell, add the following lines in the /etc/profile file (or the /etc/profile.local file on SUSE Linux Enterprise Server systems): 
if [ $USER = “oracle” ]; then 
if [ $SHELL = “/bin/ksh” ]; then 
ulimit -p 16384 
ulimit -n 65536 
else 
ulimit -u 16384 -n 65536 
fi 
fi 
For the C shell, add the following lines in the /etc/csh.login file (or the /etc/csh.login.local file on SUSE Linux Enterprise Server systems): 
if ( $USER == “oracle” ) then 
limit maxproc 16384 
limit descriptors 65536 
endif

SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SHMMAX RAM times 0.5 (note:567506.1
SHMMNI 4096 
SHMALL = SHMMAX/pagesize (note:301830.1
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500 
RMEM_DEFAULT 262144 
RMEM_MAX 2097152 
WMEM_DEFAULT 262144 
WMEM_MAX 262144 1048576 
NET.IPV4.TCP_RMEM (RMEM_DEFAULT) (RMEM_DEFAULT) (RMEM_MAX) 
NET.IPV4.TCP_WMEM (WMEM_DEFAULT) (WMEM_DEFAULT) (WMEM_MAX)

SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SEMVMX 32767 
SHMMAX 2147483648 
One-half the size of your system’s physical memory. Check your system for additional restrictions. 
SHMMNI 4096 
SHMALL = SHMMAX/pagesize (note:301830.1
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500 
To use hugepages, or to accommodate the VLM window size on Red Hat Enterprise Linux 4.0, you must increase the default maximum size of the per-process locked memory. To increase the per-process maximum locked memory limit, add the following lines to the /etc/security/limits.conf file, where oracle is the user that administers the database. Refer Note 361468.1
oracle soft memlock 5243000 
oracle hard memlock 5243000

SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SEMVMX 32767 
SHMMAX 2147483648 
One-half the size of your system’s physical memory. Check your system for additional restrictions. 
SHMMNI 4096 
SHMALL = SHMMAX/pagesize (note:301830.1
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500

           

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

Linux Itanium OS 
(See Note 225710.1 for supported kernels),(SeeNote 1130325.1 for Support Status-Oracle Database on Linux Itanium)andNote 265262.1for “Things to know about Linux”

NA

Not Available

o RHEL AS/ES 3.0 (Update 4 or higher)
2.4.21-20.EL 
o RHEL AS/ES 4.0 (Update 1 or higher)
2.6.9-11.EL 
o SuSE SLES9 (SP2 or higher) 
2.6.5-199 
o SuSE SLES-10 
o RHEL 5.0 (Note 748378.1) 
2.6.18-8 or higher 
Note: for all Itanium systems using “Montecito” processors, refer tonote:400227.1 for special installation instructions

o RHEL AS/ES 2.1 (Update 6 or higher) 
2.4.18-e52 
o RHEL AS/ES 3.0 (Update 4 or higher) 
2.4.21-27.EL 
o RHEL AS/ES 4.0 (Update 1 or higher) 
2.6.9-11.EL.smp 
o Red Flag Advanced Server 4.0 for Itanium 2 (China and Hong Kong only) 
o SuSE SLES8 (SP4 or later) 
2.4.21-278 
o SuSE SLES9 (SP1 or later) 
2.6.5-7.139 
Note: for all Itanium systems using “Montecito” processors, refer tonote:400227.1 for special installation instructions

o Red Hat Enterprise AS/ES 2.1 
2.4.18-e.14 
o Red Hat Enterprise AS/ES 3.0 
o Red Hat Enterprise AS/ES 4.0 
2.6.9-11 
o SuSE SLES8 
o SuSE SLES9 
o United Linux 1.0 
o Red Flag Advanced Server 4.0 for Itanium 2 (China and Hong Kong only) 
2.4.18-e14.ia64.rpm 
Note: for all Itanium systems using “Montecito” processors, refer tonote:400227.1 for special installation instructions

           

Linux Itanium Disk Space

NA

Not Available

1.2G Database 
1.5 to 3.5G Install

1.2G Database 
1.5G Software 
1G Companion 
150M-650M Client

4.5G

           

Linux Itanium RAM

NA

Not Available

1Gb

512Mb 
256Mb(Client/Compan)

512Mb

           

Linux Itanium swap

NA

Not Available

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

1Gb or match RAM 
512Mb(Client/Compan)

1Gb or match RAM

           

Linux Itanium tmp

NA

Not Available

400Mb

400Mb

400Mb

           

Linux Itanium JDK & JRE

NA

Not Available

JDK 1.4.2_08 is installed

JDK 1.4.2_02 is installed

o Sun JDK 1.4.1 is installed but is mandatory to patch it to 1.4.2

           

Linux Itanium Patches/ 
Packages

NA

Not Available

Red Hat Enterprise Linux 3.0:

 make-3.79.1-17

 control-center-2.2.0.1-13

 gcc-3.2.3-47

 gcc-c++-3.2.3-47

 gdb-6.1post-1.20040607.52

 glibc-2.3.2-95.30

 glibc-common-2.3.2-95.30

 glibc-devel-2.3.2-95.30

 glibc-devel-2.3.2-95.20 (32 bit)

 compat-db-4.0.14-5.1

 compat-gcc-7.3-2.96.128

 compat-gcc-c++-7.3-2.96.128

 compat-libstdc++-7.3-2.96.128

 compat-libstdc++-devel-7.3-2.96.128

 gnome-libs-1.4.1.2.90-34.2 (32 bit)

 libstdc++-3.2.3-47

 libstdc++-devel-3.2.3-47

 openmotif-2.2.3-3.RHEL3

 sysstat-5.0.5-5.rhel3

 setarch-1.3-1

 libaio-0.3.96-3

 libaio-devel-0.3.96-3

Red Hat Enterprise Linux 4.0:

 binutils-2.15.92.0.2-10.EL4

 compat-db-4.1.25-9

 control-center-2.8.0-12

 gcc-3.2.3-47 (OCCI does not support 3.4.3)

 gcc-c++-3.2.3-47 (OCCI does not support 3.4.3)

 glibc-2.3.4-2

 glibc-common-2.3.4-2

 gnome-libs-1.4.1.2.90-44.1

 libaio-0.3.102-1

 libstdc++-3.4.3-9.EL4

 libstdc++-devel-3.4.3-9.EL4

 make-3.80-5

 pdksh-5.2.14-30

 sysstat-5.0.5-1

 compat-libstdc++-33-3.2.3-47.3 Bug 4605635

SUSE Linux Enterprise Server 9:

 gcc-3.3.3

 gcc-c++-3.3.3

 glibc-2.3.3

 libaio-0.3.102-1.2ia64

 libaio-devel-0.3.102-1.2ia64

 make-3.80

RHEL ES/AS 2.1 (Update 6 or higher)

 gcc-2.96-129.7.2

 gcc-c++-2.96-129.7.2

 glibc-2.2.4-32.18

 libaio-0.3.92-1

 libaio-devel-0.3.92-1

 libstdc++-2.96-129.7.2

 libstdc++-devel-2.96-129.7.2

 make-3.79.1-8

 openmotif-2.1.30

 cfs-1.0.11 (mentioned in 10.1.0.4 Release Note but cannot find this rpm)

RHEL ES/AS 3 (Update 1 or higher)

 binutils-2.14.90.0.4-35

 compat-db-4.0.14-5

 compat-gcc-7.3-2.96.128

 compat-gcc-c++-7.3-2.96.128

 compat-libstdc++-7.3-2.96.128

 compat-libstdc++-devel-7.3-2.96.128

 control-center-2.2.01-13

 gcc-3.2.3-20

 gcc-c++-3.2.3-20

 glibc-2.3.2-95.3

 gnome-libs-1.4.1.2.90-34.2

 make-3.79-1.17

 openmotif21-2.1.30-8.i386.rpm

 setarch-1.3-1

RHEL ES/AS 4 (Update 1 or higher)

 binutils-2.15.92.0.2-13

 compat-db-4.1.25-9

 control-center-2.8.0-12

 gcc-3.4.3-22.1

 gcc-c++-3.4.3-22.1

 glibc-2.3.4-2.9

 glibc-common-2.3.4-2.9

 make-3.80-5 
Note: openmotif21-2.1.30-11.RHEL4.2 is required to install Oracle demos. 
GNU Compiler Collection (GCC) 2.96 is not supported on Red Hat Enterprise Linux 4.0. 
Gcc 3.2.3 is required for or OCCI application.

SUSE SLES8 (Service Pack 4 or higher)

 gcc-3.2.2-54

 glibc-2.2.5-230

 make-3.79.1-328

 openmotif-2.2.2-522

SUSE SLES9 (Service Pack 1 or higher)

 binutils-2.15.90.0.1.1-32.5

 gcc-3.3.3-43.28

 gcc-c++-3.3.3-43.28

 glibc-2.3.3-98.38

 libaio-0.3.98-18.3

 libaio-devel-0.3.98-18.3

 make-3.80-184.1

 openmotif-libs-2.2.2-519.4

All IA64 OS Versions – for Async I/O functionality to work you need to installPatch 3016968 on top of 9.2.0.4.0 or 9.2.0.5.0

RHEL ES/AS 2.1

 glibc 2.2.4-29

 gcc 2.96.0

 Linux Header Patch 2.4.18 (available from Intel)

 libaio-0.3.92-1

RHEL3 

1. Put gcc296 and g++296 first in $PATH variable by creating the following symbolic links. These are required for the relinking of some Oracle binaries (as root) 
# mv /usr/bin/gcc /usr/bin/gcc323 
# mv /usr/bin/g++ /usr/bin/g++323 
# ln -s /usr/bin/gcc296 /usr/bin/gcc 
# ln -s /usr/bin/g++296 /usr/bin/g++ 

2. hostname command should return the fully qualified hostname as shown below: 
– # hostname 
– hostname.domainname 

3. If any Java packages are installed on the system, unset the Java environment variables, for example JAVA_HOME. 

4. Define and export the environment variable LD_ASSUME_KERNEL before starting the install process: 
– $ export LD_ASSUME_KERNEL=2.4.19 

5. Relink error for ins_oemagent.mk – Click ignore and complete the install. Apply thepatch 3119415 

6. Apply 9.2.0.4 patchset (patch 3095277) for Linux Itanium in order to be certified and supported.

RHEL4 
9.2.0.7 patchset is required minimum patchset

 binutils-2.15.92.0.2-13

 compat-db-4.1.25-9

 control-center-2.8.0-12

 gcc-3.4.3-22.1

 gcc-c++-3.4.3-22.1

 glibc-2.3.4-2.9

 glibc-common-2.3.4-2.9

 make-3.80-5 
Define and export the environment variable LD_ASSUME_KERNEL before starting the install process: 
– $ export LD_ASSUME_KERNEL=2.4.19

SuSE SLES9 
The following requirements are needed for a successful installation of Oracle 9iR2 Linux Itanium on SuSE SLES9: 
1. Apply 9.2.0.5 patchset (patch 3501955). 
2. After installing 9.2.0.5 patchset you must install patch 4566648 to fix the following 2 issues 
4566551: BACKING STORE (BSP) NEEDS PROPER ALIGNING FOR SLES9 
4566614: BSP(BACKING STORE) VALUE SHOULD BE CHECKED BEFORE COPYING THE MEMORY SEGMENT 
3. There is a known issue, where creation of JavaVM fails during custom DB creation. Please use the workaround described as follows in case of custom Database creation. 

Remove the following eight shared libraries from $ORACLE_HOME/javavm/admin/ and restore them else where before starting database creation. 
libjox9oracle_aurora_ncomp_java.so 
libjox9oracle_aurora_server_tools_loadjava.so
libjox9oracle_aurora_sqljdecl.so 
libjox9oracle_net_nt.so 
libjox9oracle_security_jwallet.so 
libjox9oracle_sql.so 
libjox9org_omg_CORBA_2_3_portable.so 
libjox9sun_security_action.so

           

Linux Itanium Kernel Settings

NA

Not Available

Not Available

SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SHMMAX RAM times 0.5 (Note 567506.1
SHMMNI 4096 
SHMALL = SHMMAX/pagesize (note:301830.1
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500 
RMEM_DEFAULT 262144 
RMEM_MAX 2097152 
WMEM_DEFAULT 262144 
WMEM_MAX 262144 WMEM_MAX 262144 
NET.IPV4.TCP_RMEM (RMEM_DEFAULT) (RMEM_DEFAULT) (RMEM_MAX) 
NET.IPV4.TCP_WMEM (WMEM_DEFAULT) (WMEM_DEFAULT) (WMEM_MAX)

SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SEMVMX 32767 
SHMMAX 2147483648 
One-half the size of your system’s physical memory. Check your system for additional restrictions. 
SHMMNI 4096 
SHMALL = SHMMAX/pagesize (note:301830.1
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500 WMEM_MAX 262144 
NET.IPV4.TCP_RMEM (RMEM_DEFAULT) (RMEM_DEFAULT) (RMEM_MAX) 
NET.IPV4.TCP_WMEM (WMEM_DEFAULT) (WMEM_DEFAULT) (WMEM_MAX)

SEMMNI 100 
SEMMNS 256 
SEMMSL 100 
SEMOPM 100 
SEMVMX 32767 
SHMMAX 2147483648 
One-half the size of your system’s physical memory. Check your system for additional restrictions. 
SHMMIN 1 
SHMMNI 4096 
SHMSEG 4096

           

Oracle Version

11.2

11.1

10.2

10.1

               

Linux on 64-bit zSeries

Note:1306889.1 Requirements for Installing Oracle 11gR2 on RHEL 5

Note:1290644.1 Requirements for Installing Oracle 11gR2 64-bit on SLES 11
Note:1308859.1 Requirements for Installing Oracle 11gR2 on SLES 10

Not available

Note:415182.1 DB Install Requirements Quick Reference – zSeries based Linux

Note:415182.1 DB Install Requirements Quick Reference – zSeries based Linux

               

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

 

Linux on Power PC OS 
(See Note 225710.1 for supported kernels) andNote 265262.1for “Things to know about Linux”

NA

Not Available

o Red Hat Enterprise Linux AS/ES 5.0 (Update 1 or later) 
2.6.18-53.el5 
o Red Hat Enterprise Linux AS/ES 4.0 (Update 1 or later) 
2.6.9-11.EL 
o SUSE Linux Enterprise Server 9.0 
2.6.5-7.191-pseries64 
o SUSE Linux Enterprise Server 10.0 
o Asianux 2.0

See Note:341507.1 for further information

                 

Linux on Power PC Disk Space

NA

Not Available

1.2G Database 
1.5 to 3.5G Install

                 

Linux on Power PC RAM

NA

Not Available

1Gb

                 

Linux on Power PC swap

NA

Not Available

If RAM = 1024MB to 2048Mb 
then 1.5 times RAM 
elseif RAM > 2048MB and < 8192MB 
then match RAM 
else RAM > 8192MB 
then .75 times RAM

                 

Linux on Power PC tmp

NA

Not Available

400Mb

                 

Linux on Power PC JDK & JRE

NA

Not Available

JDK 1.4.2_08 is installed

                 

Linux on Power PC Patches/ 
Packages

NA

Not Available

Please refer to Note: 341507.1

Red Hat Enterprise Linux 4.0:

 binutils-2.15.92.0.2-13

 compat-libstdc++-33-3.2.3-47.3 (ppc64)

 compat-libstdc++-33-3.2.3-47.3 (ppc)
Fix for: /usr/lib/libstdc++.so.5: No such file or directory (per Rel Notes
java.lang.ExceptionInInitializerError using OUI Note 427754.1

 gcc-3.4.3-22.1 (ppc)

 gcc-ppc32-3.4.3-22.1 (ppc)

 gcc-c++-3.4.3-22.1 (ppc)

 gcc-c++-ppc32-3.4.3-22.1 (ppc)

 glibc-2.3.4-2.9 (ppc64)

 glibc-2.3.4-2.9 (ppc)

 glibc-devel-2.3.4-2.9 (ppc)

 glibc-devel-2.3.4-2.9 (ppc64)

 libaio-0.3.103-3 (ppc)

 libaio-0.3.103-3 (ppc64)

 libaio-devel-0.3.103-3 (ppc)

 libgcc-3.4.3-22.1 (ppc)

 libgcc-3.4.3-22.1 (ppc64)

 libstdc++-3.4.3-22.1 (ppc)

 libstdc++-devel-3.4.3-22.1 (ppc64)

 make-3.80-5 (ppc)

SUSE Linux Enterprise Server 9:

 gcc-3.3.3-43.34

 gcc-64bit-9-200505240008

 gcc-c++-3.3.3-43.34

 glibc-2.3.3-98.47

 glibc-64bit-9-200506062240

 libgcc-3.3.3-43.34

 libgcc-64-bit-9-200505240008

 libstdc++-3.3.3-43.34

 libstdc++-devel-3.3.3-43.34

 libaio-0.3.102-1.2

 libaio-64bit-9-200502241152

 libaio-devel-0.3.102-1.2

 libaio-devel-64bit-9-200502

 make-3.80-184.1

 binutils-2.15.90.0.1.1-32.10

 binutils-64bit-9-200505240008

An error is generated while installing Oracle Database 10.2.0.1 on Red Hat Enterprise Linux 4.0 Update 2 or later and SUSE Linux Enterprise Server 9 withservice pack 2 or later. Most of the times, the error is generated when you perform any of the following tasks:

 While installing Oracle Database 10.2.0.1 after a fresh and complete installation of Red Hat Enterprise Linux 4.0 Update 2

 While installing Oracle Database 10.2.0.1 after a fresh and complete installation of SUSE Linux Enterprise Server 9 with service pack 2 or later

 When you start dbca or netca from the command line or Oracle Universal Installer, if Standard installation is selected 
Workaround: Before installing Oracle Database 10g release 2, verify the contents of the /etc/resolv.conf file. Edit the file to make the following change: 
Change the line similar to: 
domain=my.net.com 
To: 
search=my.net.com 
The original /etc/resolve.conf file can be restored after the database installation is complete.

You must install the IBM XL C/C++ Advanced Edition V7.0 for Linux Runtime Environment Component and XL Optimization Libraries component from the following link: IBM link This URL contains information and installation instructions. All the above installations must to be done before installing Oracle database. On SUSE Linux Enterprise Server 9, install the following components:

 The RTE component: vacpp.rte.70.sles9.jan2006.update.tar.gz

 The XL Optimization Libraries: vac.lib.70.sles9.tar 
On Red Hat Enterprise Linux 4, install the following components:

 The RTE component: vacpp.rte.70.rhel4.dec2005.update.tar.gz

 The XL Optimization Libraries: vac.lib.70.rhel4.tar

Relink of 10.2 fails in Linux on Power After upgrade to RHEL U2. Apply Patch 4767801

                 

Linux on Power PC Kernel Settings

NA

Not Available

SEMMSL 250 
SEMMNS 32000 
SEMMNI 128 
SEMOPM 100 
SHMMAX RAM times 0.5 (Note 567506.1
SHMMNI 4096 
SHMALL = SHMMAX/pagesize (note:301830.1
FILE-MAX 65536 
IP_LOCAL_PORT_RANGE 9000 65500 
RMEM_DEFAULT 262144 
RMEM_MAX 2097152 
WMEM_DEFAULT 262144 
WMEM_MAX 262144

                 

Oracle Version

11.2

11.1

10.2

10.1

               

Mac OS X

NA

Not Available

Mac OS X Server 10.5.4 (Intel x86-64)

Note: Only 10.2.0.4 is available and certified only on Mac OS X Server 10.5.4 (Intel x86-64)

See the 10.2 Install Guide for MAC OS X (Intel)

Mac OS X Server 10.4(PowerPC)

Mac OS X Server 10.3.9(PowerPC)

Mac OS X Server 10.3.6(PowerPC)

               

Mac OS X Disk Space

NA

Not Available

1.2GB (optional pre-configured database) 
1.5GB to 3.5GB (software, depending on installation type)

1.2G Database 
1G Software 
1G Companion 
150M-1G Client

               

Mac OS X RAM

NA

Not Available

1GB or more

512Mb 
256Mb(Client/Compan)

               

Mac OS X swap

NA

Not Available

Equal to RAM (or more)

1Gb or match RAM 
512Mb(Client/Compan)

               

Mac OS X tmp

NA

Not Available

400Mb

400Mb

               

Mac OS X JDK

NA

Not Available

JDK 1.4.2_16 or higher

JDK 1.4.2_05 needs to be already installed 
Do this command to verify: 
$ /Library/Java/Home/bin/java -version

               

Mac OS X Patches/ 
Packages

NA

Not Available

Xcode 3.0 or later

GNU C compiler (gcc) version 4.0.1 or later (this version of gcc is included in Xcode 3.0 or later)

JDK 1.4.2_16 or higher (with the JNDI extension if you want to use the Oracle JDBC/OCI drivers)

Required Packages:

 Xcode Tools 1.1 or higher

 GNU C compiler (gcc) version 3.3 20030304 (Apple Computer, Inc. build 1635) *This version of gcc is included in Xcode Tools 1.2 or higher or in the Dec 2003 gccLongBranch Tools update.

 X11 for Mac OS X and X11 SDK for Mac OS X (Spatial only)

 OpenMotif 2.2.3 or higher (Spatial only)

               

Mac OS X Kernel Settings

NA

Not Available

Following are the recommended kernel parameters: 

kern.sysv.semmsl 87381 
kern.sysv.semmns 87381 
kern.sysv.semmni 87381 
kern.sysv.semmnu 87381 
kern.sysv.semume 10 
kern.sysv.shmall 2097152 
kern.sysv.shmmax Half the size of physical memory (in bytes) 
kern.sysv.shmmni 4096 
kern.maxfiles 65536 
kern.maxfilesperproc 65536 
net.inet.ip.portrange.first 1024 
net.inet.ip.portrange.last 65000 
kern.corefile core 
kern.maxproc 2068 
kern.maxprocperuid 2068

To improve the performance of the software on Mac OS X systems, you must increase the following shell limits:

Maximum number of open file descriptors 65536 
Maximum number of processes available to a single user 2068 

To increase the shell limits: 

1. Change directory to the following directory: 

% cd /System/Library/StartupItems/IPServices

2. Open the IPServices script using any text editor. 

3. Add the following ulimit commands to the start of the StartService function in this script: 

ulimit -Hu 2068 
ulimit -Su 2068 
ulimit -Hn 65536 
ulimit -Sn 65536 

4. Add the same ulimit commands to the /etc/rc script, before the SystemStarter command. 

Note: If you need Mac OS X Server 10.3.6, please go to here: 
Apple URL 
To obtain the latest update for Mac OS X Server 10.3.6, please go to: 
Latest Update

To obtain Mac OS X Server 10.3.9 and the software update, send an email message to oracle_update_request@iservices.apple.com . You will receive an automatic response that contains links to the required patch and to the Mac OS X Server 10.3.9 installation software. 
Note: You do not need to include a message or title with the email.

To install Oracle 10.1.0.5 on MACOSX 10.4 (Tiger OS) PowerPC based systems : 
Install Oracle Database 10.1.0.3 – software only. Please do not create the database. 
Perform a software upgrade from 10.1.0.3 to 10.1.0.5. Invoke OUI from 10.1.0.5 and choose software upgrade only. 
After 10.1.0.5 software upgrade, create database using the Database Configuration Assistant (DBCA)”. DBCA is found under $ORACLE_HOME/bin . Just Invoke this executable and choose create database option.

Following are the recommended kernel parameters:

kern.corefile core 
kern.sysv.semmni 87381 
kern.sysv.semmns 87381 
kern.sysv.semmnu 87381 
kern.sysv.semmsl 87381 
kern.sysv.semume 10 
kern.sysv.maxproc 2068 
kern.sysv.maxprocperuid 2068

To improve the performance of the software on Mac OS X systems, you must increase the following shell limits: 

Shell Limit / Hard Limit 
Maximum number of open file descriptors 65536 
Maximum number of processes available to a single user 2068 

To increase the shell limits: 

Change directory to the following directory: 

# cd /System/Library/StartupItems/IPServices 

Open the IPServices script using any text editor. 

Add the following ulimit commands to the start of the StartService function in this script: 

ulimit -Hu 2068 
ulimit -Su 2068 
ulimit -Hn 65536 
ulimit -Sn 65536 

Add the same ulimit commands to the /etc/rc script, before the SystemStarter command.

               

Oracle Version

11.2

11.1

10.2

10.1

9.2.0

9.0.1

8.1.7

8.1.6

8.1.5

8.0.6

8.0.5

 

RELATED DOCUMENTS 
————————————— 

8.0.5 to 10g Installation Guides (for AIX, HP, Sun, Tru64, Linux, MacOSX) 
http://otn.oracle.com/documentation/content.html 
Note 43507.1 ALERT:HP-UX: Patch Levels Advised 
Note 169426.1 How to change kernel mode of IBM AIX 5L (5.1) 
Note 17094.1 TECH: Unix Virtual Memory, Paging & Swapping explained 

Note 189256.1UNIX: Script to Verify Installation Requirements for Oracle 9.x version of RDBMS 
Note 250262.1RDA 4 – Health Check / Validation Engine Guide 
Note 314422.1Remote Diagnostic Agent (RDA) 4 – Getting Started 
Note 1156586.1Master Note For Oracle Database Installation 
Note 1154613.1Master Note For Cloning Oracle Database Server ORACLE_HOME’s Using the Oracle Universal Installer (OUI) 
Note 1152016.1Master Note For Oracle Database Upgrades and Migrations 
Note 1151427.1Master Note For Oracle Database Downgrade 
Note 1157464.1Master Note on Oracle Universal Installer (OUI) for installing Oracle Database Software 
Note 1157463.1Master Note For Oracle Database Client Installation 
Note 293369.1Master Note For OPatch 
Note 851598.1Master Note of Linux OS Requirements for Database Server

OS SPECIFIC COMMANDS 
—————————————–

To Find Swap, RAM, and OS Version

OS

SWAP

RAM

OS VERSION

AIX

/usr/sbin/lsps -a

/usr/sbin/lsattr -HE -l sys0 -a realmem

oslevel

HP PA-RISC

swapinfo -a

grep “Physical:” /var/adm/syslog/syslog.log

uname -a

HP Itanium

swapinfo -a

/usr/contrib/bin/machinfo | grep -i Memory

uname -a

Tru64

swapon -s

vmstat -P

/usr/sbin/sizer -v

Solaris

swap -l

/usr/sbin/prtconf | grep -i memory

uname -r

Linux

free

free

uname -a

Mac OS X

# df -h /

# /usr/sbin/system_profiler SPHardwareDataType | grep Memory

# sw_vers

To Determine the Unix Kernel Parameters

OS

LOCATION

COMMAND TO SEARCH

AIX

automatically configured

do ‘env’ for LINK_CNTRL, 
To determine if AIX is 64 bit enabled do ‘genkex | grep 64’ or ‘genkex | grep call’ (see Note 1019106.102)

HP

/stand/system or use SAM –>Kernel Configuration

/etc/sysdef, /usr/sbin/kmtune (kmtune desupported in 11.31, use /usr/sbin/kctune -v), or /usr/sbin/kcweb -F

Tru64

/etc/sysconfigtab

/sbin/sysconfig -q ipc or /sbin/sysconfig -q vm or /sbin/sysconfig -q proc

Solaris

/etc/system

“/etc/sysdef | grep SHM” or “/etc/sysdef | grep SEM”

Linux

/usr/src/linux/include/asm/shmparam.h
/usr/src/linux/include/linux/sem.h 
/proc/sys/kernel/sem 
/proc/sys/kernel/shmall 
/proc/sys/kernel/shmmax 
/proc/sys/kernel/shmmni

ipcs -lms

Mac OS X

/etc/sysctl.conf

“# /usr/sbin/sysctl -a | grep “

O/S Software Installed Packages and Patches

OS

COMMAND FOR PACKAGES

COMMAND FOR PATCHES

AIX

lslpp -w | grep -i “software title” (applies to APARs and PTFs)

/usr/sbin/instfix -ik patch number

HP

Prior to 11: /usr/sbin/swlist -lproduct PH\* hp-ux 11 and after: * /usr/sbin/swlist -l patch \*\.*,c=patch * /usr/contrib/bin/show_patches (from patch PHCO_19550)

/usr/sbin/swlist -l fileset | grep -i

Solaris

/bin/pkginfo -l | grep -i “software title”

/bin/showrev -p

Tru64

/usr/sbin/setld -i | grep -i “software title”

/usr/sbin/setld -i | more
For patchkits:
/usr/sbin/dupatch -track -type kit

Linux


To see if a particular RPM is installed (without the architectur): 
$ rpm -qa | grep “package name” 

To see if a particular RPM is installed (with the architectur): 
$ rpm -qa –qf “%{NAME}-%{VERSION}-%{RELEASE}_%{ARCH}\\n” | grep “package name” 

To see what RPM provided a particular object/library: 
$ rpm -q –whatprovides –qf “%{NAME}-%{VERSION}-%{RELEASE}_%{ARCH}\\n” “full path/library name” 

To see the contents listing of an RPM: 
$ rpm -ql “RPM name” 
For example: $ rpm -ql compat-libstdc++-33-3.2.3-47.3.ppc 
/usr/lib/libstdc++.so.5 
/usr/lib/libstdc++.so.5.0.7

 

Mac OS X

to be supplied later

to be supplied later

To Check if an OS is 64 bit Capable or not

OS

COMMAND

RESULTS

Aix

lslpp -L | grep 64bit

It should return “bos.64bit”

HP

getconf KERNEL_BITS

It should return “64”

Solaris

/bin/isainfo -kv

If the isainfo command does not exist it is not 64-bit. It should return “64-bit sparcv9 kernel modules”

To Check version of Compiler

COMPILER

COMMAND

C/C++

do a “which cc”, then cd to the directory it is in, then do a “what cc” 
except for Linux, on Linux do a “rpm -qa | grep egcs

COBOL

cd $COBDIR and do “more cobver”

Fortran

do a “which f77”, then cd to directory it is in, then do a “what f77”

CHANGE HISTORY


===============

111704 
– HP section – HP Doc BUG ID: KBRC00003627is not applicable to 11.22 and 11.23 
– TRU64 section – Added OSFX11 as required package for 10g and 9.2

120404 

– Linux section – Added Asianux and Red Flag requirements, Updated certified OS’s and their kernel versions and the required OS packages for each OS

121204 
– Linux section – Added reference to 
Note 252217.1 for additional setup requirements for RHEL3 and 9.2 x86 
— Added additional steps for SLES9 for 9.2 32bit x86

121904 
– Linux section – Updated Linux Itanium 10g on SuSE SLES9 required RPMs

122604 
– Linux section – Added LD_ASSUME_KERNEL=2.4.19 to 10g RHEL3 section

122704 
– MacOSX section was added

010205 
– Linux section – 10g SuSE SLES9 references to gcc-3.3-43 and gcc-c++-3.3-43 were corrected to gcc-3.3.3-43 and gcc-c++-3.3.3-43

011005 
– Linux section – Added reference to Note 265262.1 for “Things to know about Linux”

012905 
– General section – Removed reference to the HCVE script for Linux 64 and added references to newly created Linux IA64 and Linux AMD64. 
— Added reference to newly created Mac OSX HCVE script

020505 
– HPUX section – Added 11.23 (PA-RISC) (64bit) to 10g and 9.2 as a certified OS 
– Sun section – Added SUNWuiu8,SUNWulcf (if Bug 4025250 occurs) to 10g OS packages

022505 
– AIX section – Added AIX_THREAD_SCOPE=S to 9.2 
– TRU64 section – Added VM_BIGPG_ENABLED 0 to 10g and 9.2 kernel settings 
– General section end of Note – Updated the swlist commands for checking HP OS patches and packages

022805 
– HPUX section – For 10g and 9.2 added/update that MAXSWAPCHUNKS, SEMMAP, and VX_NCSIZE are obsolete on 11.23 PA-RISC and IPF and no longer need to be set also to now set NCSIZE = (NINODE+1024)

031805 
– HPUX section – Update 10g 11.11 OS patches that PHNE_28476 is superseded by PHNE_29825, PHCO_26331 s/b PHCO_27958, PHKL_26468 s/b PHKL_27316

040905 
– TRU64 section – Removed 5.1 as being certified with 9.2, updated that 5.1a requires PK6 now versus PK3 and updated that 5.1b requires PK4 now versus PK2 
— Also added require patches for each newly required patchkit 
— Modified the new_wire_method to indicate thatif you are at 5.1a PK6 it should be set to 1

041005 
– Sun section – Added Solaris 10 as now certified with 10g and 9.2 and special instructions 
– Linux section – Added RHEL4 as now certified and its needed environment settings and rpms

041605 
– General section – Added Change History

042305 
– Linux section – 9.2 x86 for SuSE9 added needed patch 3809563 if applying 9.2.0.5 patchset 
— Clarified that patch 4190568 needs to be applied on top of 9.2.0.6 patchset 
— Added Async IO patch 3016968/patch 3208258 in 9.2 x86 section 
— Added Async IO patch 3016968 in 9.2 IA64 section

042505 
– Tru64 section – 817 column changed vm-mapentries that it applies to OS versions below 5.0, starting in 5.0 it is autoset

043005 
– AIX section – Kernel Settings, clarified that AIXTHREAD_SCOPE is an environmental setting not a kernel setting

052205 
– Linux section – 10g x86_64 for SuSE SLES9 added glibc-32bit-8.1-9 and glibc-devel-32bit-8.1-9 as required packages per <> 
– Sun section – made SUNWmfrun a mandatory patch for 10g and 9.2 per <> 
— Updated Kernel settings for Solaris 10 because most are obsoleted

060305 
– Linux section – Corrected the 9.2 section that patch 3016968 and patch 3208258 are specific to RHEL3 and not all x86 OSs

070305 
– OS Specific Commands section – O/S Software Installed Packages and Patches Linux section – Added RPM commands to list an RPMs contents and query RPMs to see which one provides a specific object library

072205 
– Linux section – 9.2 Linux Itanium Added RHEL3 requirements 
– Linux section – 10g IBM zSeries SuSE SLES9 added libc6.2-2.so.3 32bit as a requirement per <>

072305 
– Linux section – Added 10.2 Linux x86 requirements 
– HPUX section – updated 9.2 11.0 patch section with new superseded patches

082205 
– Sun section – Modified the Solaris 10 special instructions per <> 
– TRU64 section – corrected value of SHM_MIN to be 1 instead of 1024 in the 9.2 section per <>

082905 
– AIX section – Added 10gR2 requirements, presently OTN states to use 10gR1 requirements 
– HP section – Added 10gR2 requirements, presently OTN states to use 10gR1 requirements 
– Added note to ensure that unzip 5.5 or later is being used in the 10g and 9.2 section per <> 
– Sun section – Added 10gR2 requirements, presently OTN states to use 10gR1 requirements

091705 
– Sun section – Updated 10gR2 requirements since the Installation Guide is now available

091805 
– AIX section – Updated 10gR2 requirements since the Installation Guide is now available 
– HPUX section – Updated 10gR2 requirements since the Installation Guide is now available 
– Linux section – Updated 10gR2 requirements since a new Release Note has the correct RPMs for RHEL4 and SuSE9

092605 
– Pre-Installation Scripts – Added new heading 
– Added 10gR2 Pre_Installation Script Notes

100405 
– HPUX section – Added comment to 9.2 NCALLOUT is obsolete in 11.23 
– Sun section – added SUNWuiu8, SUNWulcf as required to 9.2

100705 
– AIX section – Added APAR IY68989 to 10gR2 AIX 5.3 per Release Note 
– Related Documents – added 10gR2 Pre-Installation scripts

101005 
– Linux section – Added Note 303859.1 for 9206 on RHEL4 
– Added Patch 3208258 as neeeded for AIO on SLES9

101905 
– Linux section – Added RHEL4 for 10gR1 x86_64 requirements now that it is certified

110705 
– Linux section – Added 10gR2 x86_64 requirements now that it is certified 
– Added glibc-devel rpm as required for 9.2 x86 on RHEL3 
– Added xFree86-libs as required to 10gR1 x86_64 for RHEL4 (Bug 4387087
– Added glibc-devel-32bit-9 to 10gR1 x86_64 for SuSE SLES9 (Bug 4405422
– Added to 9.2 IA64 the SuSE SLES9 is now certified 
– Added to 10gR2 on RHEL3 that it requires Update 4 
– HPUX section – Added supecedes of patches for 10gR1 on 11.11

111105 
– entire document – made all patches/bugs hyperlinks, removed double entry of compat-db in RHEL3 for 10gR2 X86_64

111805 
– Linux section – Added needed RPMs and reference to Ivan Kartik document for install of 9.2 on SuSE SLES 9

120805 
– Linux section – Added RHEL4 to 10gR1 Linux IA64 as certified – Added Linux on Power PC requirements

121105 
– HPUX section – Updated the 9.2 11.11 patch list 
– Sun section – Updated special instructions for Solaris 10 and 10gR1

121805 
– Linux section – Added 10gr2 on Linux IA64

010606 
– Linux section – Added compat-libstdc++-296-2.96-132.7.2 (i386) to 10gR1 Linux x86 for RHEL4 
– Added RHEL4 for 9.2 x86_64 as certified 
– Sun section – modified noexec_user_stack is not obsolete to Solaris 9, it is actually still valid for Solaris 9 and 10

012706 
– Pre-Installation Scripts – Added 10gR2 Linux AMD64/EM64 script 
– Linux section – Changed 10gR2 Linux x86_64 for RHEL3 to show the compat-gcc, compat-gcc-c++, compat-libstdc++, and compat-libstdc++-devel as 32bit RPMs not 64bit RPMs 
– Added glibc-32bit, glibc-devel-32bit, libaio, libaio-devel to 10gR2 Linux x86_64 for SLES9

021106 
– Linux section – corrections to 10gR2 Linux on PPC – RHEL4 and SLES9 RPMs 
– Added reference to Note:353529.1 and added the suggested RHEL4 RPMs for 9.2.0.7 on Linux x86_64 
– Added XFree86-libs-4.3.0-78.EL.i386.rpm per Remark 56677.1 

021306 
-HP section – Added the new 10gR2 HPUX Itanium requirements 
-Linux section – broke out the section into four sections – Linux x86, Linux x86_64, Linux Itanium, and Linux on Power PC for ease of reading

021506 
-TRU64 section – Incorporated Remark 56834.1 and modified the 9.2 kernels related to “per_proc”:ref: TRU64 Tuning Oracle 817 and higher and Note:201200.1 
-Linux section – Incorporated Remark 56763.1 – Removed reference to xscreensaver-4.16-2.6 from 10gr2 x86 and x86_64 for SuSe SLES9

021706 
-HPUX section – For 10.2 HPUX Itanium added OS patch requirements for ProC/C++/OCI/OCCI/XML

022406

 -HPUX section – Added supercessions to 10gR2 HPUX PA-RISC and Itanium patches

022806 
-Linux section – Added libaio-0.3.96 to 10gR2 X86

030606 
-Linux section – Changed the kernel version for 10gR2 on Linux Itanium for SuSE SLES9 from 2.6.5-7.139 to 2.6.5-7.199 which is what SP2 is.

031006 
-Linux section – Added compat-libstdc++-33-3.2.3-47.3 to 10.2 RHEL4 Linux x86 per Remark:57408.1 
– modified gcc and g++ RPM versions for 10.2 on RHEL4 Linux x86_64 to be 3.4.3-9.1 instead of 3.4.3-9.EL4 
-Sun section – Added SUNWxcu4 per Remark 57401.1

031306 
-Linux section – corrected 9.2 x86_64 SuSE SLES9 details as they were referencing x86 requirements by mistake, changed note reference from Ivan Kartik’s to Fabrizio Magni’s

031606 
-Linux section – changed 9.2 on x86 on RHEL4 to also be certified with 9.2.0.5 patchset and patch 4276910 
-Sun section – changed 9.2 (32bit) on Solaris 10 to be certified on minimum 9.2.0.4 patchset instead of 9.2.0.6 and 9.2 (64bit) on Solaris 10 to be certified on minimum 9.2.0.5 instead of 9.2.0.6 per My Oracle Support (MOS) – Certification

031706 
-HPUX section – updated the 10.1 version on HPUX 11.11 OS patches to reflect latest superseded versions. 
-Linux section – changed 10.2 x86_64 on RHEL4 to add binutils-2.15.92.0.2-18.x86_64.rpm as another version of binutils that can be installed.

032506 
-Linux section – updated Linux Itanium for 9.2 to add RHEL4 requirements (per Remark 57699.1) 
-Mac OS X section – Added that 10.1.0.3 is now certified on 10.3.9 (per Remark 57702.1) 
-Sun section – Added SUNWuiu and SUNWulcf to 10.2 on Solaris 8,9, and 10 (Per Remark 57701.1) 
– Added that 10.2.0.2 is now certified on Solaris x86_64/AMD64

041806 
-Linux section – 10.1 x86 on RHEL4 clarified the RPMs (Remarks 58081.1, , 58342.1, 58435.1) 
– 9.2 x86_64 on SuSE 9, remove external reference, added LD_ASSUME_KERNEL=2.4.20 (Remark 58338.1) 
– All references where SHMMNI was set lower then SHMSEG, the value of SHMMNI was set to match it (Remark 57854.1) 
– 10.2 x86_64 on RHEL4 – Clarified architecture of RPMs and added RPMs as requested by T. Yoshimura and <>

041906 
-Linux section – 10.1 x86_64 on RHEL3 added XFree86-libs (32bit) is required.

043006 
-Linux section – 10.2 x86_64 on SLES9 changed glibc-32bit-8,glibc-devel-32bit-8 to -9

050706 
-Sun section – Added 112963-25 as a required Solaris 9 OS patch (Bug 4712475) per R. Gulledge

051806 
-Linux section – 9.2 x86_64 on RHEL3 added Note 308588.1 and LD_ASSUME_KERNEL=2.4.19 
– 9.2 x86_64 on SLES9 added Note 361169.1 and glibc-32bit and glibc-devel-32bit

052406 
-Sun section – 10.2 added Patch 4589082 as needed prior to install to deal with -ldce not found issue when linking proc

082806 
-Linux section – Removed references to ORBit-0.5.17-14.i386.rpm and gnome-libs-1.4.1.2.90-44.1.i386.rpm fo3 10g2 on RHEL4 x86_64 as no valid reference can be found.

091806 
-Linux section – 10.1 x86_64 on RHEL4 updated OS package requirements.

092206 
-Linux section – 10.2 Itanium on RHEL4 added compat-libstdc++-33-3.2.3-47.3 to OS package requirements.

101706 
-Linux section – 10.1 x86 on RHEL3 updated OS package requirements.

110706 
-Tru64 section – Added the new 10gR2 Tru64 requirements

112806 
-Linux section – 10.2 x86 on SLES9 updated OS requirements

121206 
-Linux section – all versions and platforms – changed SHMALL to formula

121906 
-Linux section – 10.2 x86_64 on SLES10 – added os version and package reqs

022707 
-HP-UX section – 10.2, 11.11 required patches – added new superseded patch numbers

030607 
-Added reference to note:400227.1 for all Itanium systems with “Montecito” processors

030607 
-Added section/links for 64-bit Linux on zSeries

032007 
-Added HP-UX Itanium 11.23 info for 9.2.0, 10.1.0, and 10.2.0

040407 
-Aix section – Added APAR IY94343 – LV Block Corruption Note 422031.1 (per Remark 70417.1)

042507 
-Sun section – Added Solaris 10 kernel parameters

052307 
-AIX section – added reference to Note 282036.1 for AIX 5.3 and 5.2 patching requirements 
-Linux section – modified that SHMMAX should not be set higher then 4Gb due to core dumping generation issues.

052507 
-HPUX section – added to the 11.31 obsolete parameters that they are applicable to PA-RISC too. 
-Linux section – for the Linux on PPC added for RHEL4 that glibc-devel (ppc) and glibc-devel (ppc64) are required per Bug 5436180

053007 
-Related Documents section – resolved a problem with a broken link

061307 
-Linux section – corrected version number of libaio for RHEL4 on Linux x86 from 0.3.96 to 0.3.102-1 per Remark 73923.1

071807 
-Linux section – Moved footnotes for Linux x86_64 9.2 on RHEL3 directly beneath the section (per Remark 75021.1) 
– Added LD_ASSUME_KERNEL to Linux Itanium on RHEL4 (per Remark 75729.1) 
– Added OEL4 and OEL5 as certified for 10.2 on Linux x86 and Linux x86_64 (per Remark 75767.1)

072507 
-Sun section – change comment to 112760-05 to state that it is needed for Native PL/SQL only, not generic PL/SQL.

080107 
-Linux section – added default-rpm NOTE 386391.1 to SLES9 x86-64 section per Remark 76324.1

081707 
-Linux section – added 11gR1 requirements for Linux x86.

082207 
-Linux section – 11.1 x86 corrections, 10.2 SLES9 x86_64 corrections, made it consistent with Note 339510.1, addressed Remarks 77473.1,77604.1,77657.1,77682.1

091207 
-Linux section – 10.2 x86 and x86_64 for [Red Hat,Oracle] Enterprise Linux requirements added (per Remark 78415.1) 
-Tru64 section – 10.2,10.1, 9.2 changed the 5.1B required patchset to match the 10.1.0.5/9.2.0.8 patchset READMEs higher level. (per Remark 78544.1)

091907 
-Sun section – Added patches needed for Fair Share Scheduler on Solaris 10 
-Tru64 section – Clarified setting of NEW_WIRE_METHOD on 5.1B PK5

100307 
-Linux section – Clarified 10.2 Linux Itanium on RHEL4 requirements (per Remark 79375.1) 
– Clarified 10.1 Linux Itanium section based on 10.1.0.4 Patchset Readme (per 79375.1) 
-Tru64 section – changed default per_proc_stack_size to 32M to help avoid ORA-4030s (per Remark 79349.1)

101707 
-Main section – Removed Pre-Installation Script notes as they are now decommissioned (Remark 81013.1) 
– added OPatch section 
-Linux section – Added/Modified RHEL5/OEL5 10.2 Linux x86_64 rpms list per Release Note (Remark 80909.1) 
– Removed reference to Note 301830.1 from Linux x86 section as it is for Linux x86_64 (Remark 80978.1)

102207 
-Linux section – Added 11g on Linux x86_64 requirements

102307 
-Linux section – Updated 10.2 on Linux on PPC (Remark 81403.1)

110707 
-Mac OS X section – Updated certification section and fixed broken links (Remark 81782.1) 
-Sun section – Fixed broken links to Sunsolve (Remark 81766.1) 
-Tru64 section – Fixed broken links to HP support (Remark 81769.1)

111407 
-Linux section – Added net.ipv4.tcp_rmem and net.ipv4.tcp_wmem to 11g Linux x86 (Remark 82482.1) 
– Modified required RPMs for OEL/RHEL5 for 10.2 on x86 as updated in Note 419646.1 (Remark 82777.1) 
– Removed reference to OEL5 document as it has been merged into Note 419646.1 (Remark 82778.1) 
– Modified required RPMs for OEL/RHEL5 for 10.2 on x86_64 as updated in Note 421308.1 (Remark 82779.1) 
– Removed reference to OEL5 document as it has been merged into Note 421308.1 (Remark 82780.1) 
– added compat-gcc-32-c++ rpm and Patch 5240469 to 10.2 on x86_64 on RHEL4

111607 
-AIX section – added 11g requirements 
-HPUX section – added 11g requirements for HPUX Itanium 
-Sun section – added 11g requirements

112907 
HP section – added 11.1 requirements for HPUX PA-RISC 
– Removed special installation reference for 10.1 on HPUX Itanium as there are none (Remark 83375.1) 
-Linux section – change RMEM_DEFAULT to 4194304 for 11.1 on RHEL5,OEL5 on X86_64 (Remark 83748.1) 
-Sun section – added SUNWuiu8 and SUNWulcf to 11.1 (Remark 83714.1)

120507 
-Linux section – Added net.ipv4.tcp_rmem and net.ipv4.tcp_wmem to 10.2 Linux x86 (Remark 83919.1)

121307 
-Linux section – Modified net.ipv4.tcp_rmem and rmem_max and rmem_default to 10.2 Linux x86 (Remark 84422.1)

121907 
-HPUX section – Updated 11.1 and 10.2 HPUX OS patch requirements with superseding patches (Remark 84854.1)

013008 
-AIX section – added Bug 5496862 as a requirement for running AIX 5.3 ML 5 (Remark 91473.1)

022708 
-AIX section – added 6.1 as certified to 10.2 (Remark 92899.1) 
– added IZ03475 for 5.3 ML7 to address ORA-27061 (Remark 92047.1) 
-HP section – added kctune to OS commands now that 11.31 desupports kmtune (Remark 91954.1) 
-Linux section – Update 9.2 on x86_64 on RHEL4 and removed requriement for gnome-libs and Orbit (32bit rpms) (Remark 91893.1) 
-Sun section – Added that Update 6 is required for Solaris 9 with 10.2 and Update 7 for Solaris 8 (Remark 92015.1)

030508 
-HP section – added more comments regarding 11.31 and -ignoresysprereqs (Remark 94177.1)

031808 
-Linux section – Added kernel paramaters NET.IPV4.TCP_RMEM and NET.IPV4.TCP_WMEM to x86_64 and Itanium (Remark 94274.1 and 94741.1)

031908 
-HPUX section – Corrected SHMMIN and SHMSEG settings for 11.1 on PA-RISC and IPF 
-Sun section – Added month/date to give reference to Solaris Update levels

032108 
-HPUX section – Removed reference to JDK 1.1.8 for 9.2 (Remark 95270.1) 
-MAC OSX – Removed broken link

032608 
-Linux section – Added SLES10 and Asinux 2.0 to cerified for Linux on Power for 10.2

041608 
-Linux section – corrected typo on compat-libstdc++-devel for Linux x86 on 10.2

042308 
-HPUX section – due to Bug 6995956 changing formula for maxuprc to be (nproc*9/10)+1 (Remark 97557.1) 
-Sun section – Added 113029-07 as a required patch for Solaris 9 if using the Fair Scheduler ref: Note 558374.1 (Remark 97290.1)

092308 
– All requests till September 20,2008 incorporated – Patch 6880880 details, Linux X86-64 11GR1 now pointing to correct Note 437123.1 
– Obsolete kernel parameters in HP-UX 11.31 – MSGSEG & NFILE documented, added SLES-10 certification 10GR2 64 Bit on Linux (Itanium) 
– 11GR1 install on Solaris 5.9 update 7 or higher is required, 11GR1 install on AIX requires 5.3 ML6 or higher is required 
– OS Kernel update statement added under PURPOSE section. HP-UX 11.31 PHKL_35936 has been superseded by PHKL_38449 
– 11GR1 install on AIX – PATCH 5496862 is required (see Note 390656.1).Note 567506.1 reference added to clarify SHMMAX size

100908 
– HP Itanium 11.31 PHKL_37185 superseded by PHKL_38038 
– SUN SPARC Solaris 10 Patch 127111-02 required for 10.2.0.4.0

103008 
– HP-UX 11.31 with 10GR2. 4 HP-UX Patches required as per Part Number B25292-06 
– AIX OS supported configuration for 11.1 as per Part Number B32076-03 
– Relink of 10.2 fails in Linux on Power After upgrade to RHEL U2. Apply Patch 4767801 
– SUN 10 with 11.1. Required SUN Patch 137111-04 as per Part Number B32314-02 
– HP-UX on OS 11.31 supported on 9.2

012209 
– HP-UX superseded PPHSS_36343 with PHSS_38140 
– HP-UX superseded PHSS_37201 with PHSS_38134 
– AIX 5L required or above required for 10.2.0.4.0 & above as per NOTE 739371.1 
– AIX 6.1 required packages for 11.1.0.6.0 
– HP-RISC / HP-Itanium 11.31 support for 10.2 
– Link to internal BUG 6613550 removed 
– RHEL5.0 on Linux Itanium (ia64) 
– OEL5 / RHEL5.0 rpm changes. Refer Note 421308.1 & Note 419646.1 
– AIX issue addressed in Note 422031.1 
– HP-UX 11.23 Itanium PHKL_33807 superseded by PHKL_38364 
– HP-UX 11.23 Itanium PHKL_36667 superseded by PHKL_37653 
– HP-UX 11.23 Itanium PHSS_37492 superseded by PHSS_34444 
– HP-UX 11.23 Itanium PHSS_37498 superseded by PHSS_38138 or PHSS_39101 
– HP-UX 11.23 Itanium PHSS_37492 superseded by PHSS_38134 
– HP-UX 11.23 Itanium PHCO_36323 superseded by PHCO_37940 
– RHEL5 certified on 10.2. Refer to Note 748378.1

020509 
– HP-Itanium NFLOCKS, SEMMNI & MSGTQL parameter changes for 10.2. Part Number B25293-01. Web site below :- 
– http://download.oracle.com/docs/cd/B19306_01/install.102/b25293/pre_install.htm#BABJHCJI 
– Solaris patches 117837-05, 117846-08 & 118682-01 are only required for Solaris X86 – BUG 6968216 
– On AIX 5.3 with 9.2 use -ignoreSysPrereqs with runInstaller (Note 293750.1) 
– SEMMNS, SEMVMX & SHMMNI masked as Obsolete as per http://docs.sun.com/app/docs/doc/817-0404/appendixa-6?l=en&a=view&q=shmmax

022709 
– HP-Itanium NFLOCKS, SEMMNI & MSGTQL parameter changes for 9.2 & 10.1. 
– 10.2,10.1 & 9.2 – Oracle Solaris 10 install Sun patch 127111-03 (SPARC) / 127127-11 (x86-64) See Note 460424.1

032409 
– net.ipv4.tcp_rmem & net.ipv4.tcp_wmem are no longer required for standalone install

050509 
– IP_LOCAL_PORT_RANGE changes 9000 65500. Refer Note 339510.1 & Note 419646.1 
– 11.31 (PA-RISC) required patches. Part Number B19067-08. Refer Section 4.1 Operating System Filesets for HP-UX 11.31. Web site below :- 
– http://download.oracle.com/docs/cd/B19306_01/relnotes.102/b19067/toc.htm 
– AIX with 11.1 changes:- 
– xlC.aix50.rte:8.0.0.7 or later (AIX 5.3) 
– xlC.rte:8.0.0.7 or later (AIX 5.3) 
– xlC.aix61.rte:9.0.0.1 or later (AIX 6.1) 
– xlC.rte:9.0.0.1 or later (AIX 6.1) 
– rmem_default=262144 for 11.1, 10.1 & 10.2 
– rmem_max for 11.1 is 4194304. rmem_max for 10.1 & 10.2 is 2097152 
– wmem_default=262144 
– tcp_rmem & ipv4.tcp_wmem are no longer required for standalone install 
– HP-UX (Itanium & PA-RISC) with 11.1 MAXTSIZE_64BIT 1073741824 
– Mac OS X – 10.2.0.4 available on Mac OS X Server 10.5 (Intel x86-64) 
– Sun OS 137111-04 s/b 137137-09. Refer http://sunsolve.sun.com/search/document.do?assetkey=1-21-137137-09-1 
– Sun OS 127111-02 s/b 127127-11. Refer http://sunsolve.sun.com/search/document.do?assetkey=1-21-127127-11-1 
– Sun OS 127111-03 s/b 127127-11. Refer http://sunsolve.sun.com/search/document.do?assetkey=1-21-127127-11-1 
– AIX 5.3. Added IY84780. Refer http://www-01.ibm.com/support/docview.wss?uid=isg1IY84780 
– AIX 5.3. Added IY68989. Refer http://www-01.ibm.com/support/docview.wss?uid=isg1IY68989 
– HugePages on 64-bit Linux. Fixed hard memlock 5243000 & soft memlock 5243000 values. Refer Note 361468.1

061009 
– HP-UX 11.23 (IA64) OS Patches updated with 9.2.0. Same OS Patches as HP-UX 11.22 (IA64)

071409 
– rpm’s compat-gcc-34-3.4.6-4 & compat-gcc-34-c++-3.4.6-4 are not required for RHEL 5 & OEL 5 
– MSGMAP,MAXSWAPCHUNKS, NCALLOUT, SEMMAP,VX_NCSIZE,NFILE, MSGSEG are obsolete on 11.31 (Itanium and PA-RISC) and no longer required to be set

080309 
– Fix from Note 301665.1 incorporated for 11GR1 on Linux X86_64

090909 
– 11GR2 requirements for Linux X86 32 BIT & Linux X86 64 BIT added

091809 
– Fix swap details for Linux X86 64 Bit. If RAM greater than 14Gb then 10Gb 
– Symbolic links not required for HP Itanium on 11GR1 as per Bug 8789180 
– 11GR1 with Linux X86 64 BIT has reference to Note 437123.1 & Note 301665.1 
– Oracle Solaris 8 with 10.2 missing packages list included. Refer to Note 366100.1 
– Patch PHKL_38397 or later required on HP OS 11.31. Patch PHKL_37809 or later required for HP OS 11.23. Refer to Note 580273.1. Changes incorporated for 11GR1 & 10GR2. 
– ulimit changes for Sun SPARC & 11GR1. Refer to Note 250262.1 
– SHMMAX RAM reference added for Linux X86 32 BIT & Linux X86 64 BIT for 11GR1 & 10GR2. Refer to Note 567506.1.

121709 
– 11GR2 Sun Sparc 64 BIT added 
– 11GR2 Install Guide http://download.oracle.com/docs/cd/E11882_01/install.112/e10848/pre_install.htm#BABBBDGA 
– 11GR2 Install Guide for SUN Sparc – Part Number E10848-03 
– Linux X86-64 BIT. Added – kernel.shmall – Reference Note 301830.1, kernel.shmmax, kernel.shmmni, kernel.sem 
– For 11GR2 & 11GR1 FILE-MAX value is 6815744. This is as per Bug 9140073 
– Fixed PHKL_38397 or later 
– Columns had moved for HP & were showing differently in Intenet Explorer & Fire Fox. Now Fixed

021110 
– 11GR2 install details for AIX. Part Number E10854-01. 
– 11GR2 AIX Install Guide http://download.oracle.com/docs/cd/E11882_01/install.112/e10854/pre_install.htm#CIHFICFD 
– 11GR2 install details for HP. Part Number E10851-01. 
– 11GR2 HP-UX Install Guide http://download.oracle.com/docs/cd/E11882_01/install.112/e10851/pre_install.htm#CIHEIFDE 
– 11GR2 HP-UX Itanium Install Guide http://download.oracle.com/docs/cd/E11882_01/install.112/e10869/toc.htm 
– 11GR2 install details for HP-UX Itanium.Part Number E10869-01

021910 
– 10GR1 with HP-UX 11.31 (Itanium & PA-RISC). Added obsolete parameters Nfile and Msgseg 
– 9.2.0 with HP-UX 11.31 (Itanium & PA-RISC). Added obsolete parameters Nfile and Msgseg 
– 11GR2 with AIX 6.1, kernel has been upgraded to 6100-02-05 from previous level 6100-02-01. 
– 11GR2 with AIX 6.1. APR have been removed with the upgraded kernel 6100-02-05

022310 
– IBM JDK version for 11GR2

031810 
-AIX parameters export AIXTHREAD_SCOPE=S for 11GR2 as per Part Number E10839-04

072110 
-Swap requirements for 11GR2 for various platforms are in sync with Release Notes 
-Swap requirements for 11GR1 for various platforms are in sync with Release Notes 
-HP-UX OS Patches superseded for 10GR2. PHSS_37492 s/b PHSS_40537,PHKL_37653 s/b PHKL_41002 
-HP-UX OS Patches superseded for 10GR2. PHSS_38134 s/b PHSS_40537, PHSS_39101 s/b PHSS_40541 
-HP-UX OS Patches superseded for 10GR2. PHSS_34445 s/b PHSS_40547, PHSS_38140 s/b PHSS_40543 
-HP-UX OS Patches superseded for 10GR2. PHSS_38134 s/b PHSS_40537, PHSS_36344 s/b PHSS_40539 
-HP-UX OS Patches superseded for 10GR2. PHCO_37940 s/b PHCO_39699, PHSS_37492 s/b PHSS_40537. 
-Oracle 11GR1 install on AIX Power 7 will fail without a Patch 9216848. Doc ID 1065579.1. 
-Patch 6613550 has been superseded by 6718715 for AIX on 10GR2. 
-net_core.wmem_max value on Linux changed to 1048576 for 11GR1. 
-For 11GR2 & 11GR1 FILE-MAX value is 6815744. This is as per Bug 9140073.

072910 

Master Note For OPatch (Doc ID 293369.1) 
Patch Set Update (PSU) with Opatch details 
Master Note addition under Related Documents Section

082010 
Master Note list updated with Note 293369.1 & Note 851598.1

100610 
10GR2 and 11GR1 on Linux x86 and Linux x86-64 are also certified on SLES11 
Changed Asianux 3.0 to Asianux Server 3 
Added Asianux Server 3 SP2 to Linux x86 & Linux X86-64 BIT for 11GR2 
Disk Space and tmp size for 11GR1 on AIX modified as per Installation Guide 
Note 1130325.1-Support Status-Oracle Database on Linux Itanium added to Linux Itanium OS section 
RAM size consistent to 4GB for 11GR2 on HP, AIX, SUN & LINUX X86 64 BIT. Based on BUG # 9491478

120310 
PA-RISC added for 10GR1 & 10GR2 for OS 11.11. Previous entry was just saying 11.11 (64bit). Now says 11.11 (PA-RISC) (64bit) 
Broken Link for HP Kernel settings is fixed for 11GR2 
Patch#5496862 as mandatory for Releases: 8.1.7 to 10.2 as stated in Note#390656.1 – IO Interoperability Issue between IBM ML05 and Oracle Databases.

122410 
Maximum SHMMAX values for Linux x86 and x86-64 has been updated with the revised position from NOTE 567506.1

121311 
11.2 on AIX: rsct.basic.rte and rsct.compat.clients.rte filesets are required for RAC configurations only 
11.2 on zSeries Linux: added links to articles containing 11.2 requirements 
Replaced Metalink references with My Oracle Support (MOS) references

012312 
Solaris: 11.2.0.3 certified on Solaris 11 (SPARC and Solaris x86-64) 
Solaris: Updated link to 11g Install Guide 
Solaris: Solaris 8 patch 108940-76 or higher (not patch 112771-30) required for 10.2 
Solaris: As per 11g Install Guide, recommended command to check swap is “swap -l” not “swap -s” 
AIX: 11.2 certified on AIX 7.1 (with some required patches/packages) 
Linux x86_64: 10.2 certified on SLES11

012412 
10.2 certified on IBM Linux on Power RHEL5

012512 
AIX: Updated list of required APARs for 11.2 and link to 11.2 Install Guide 
AIX: Clarified that 10.2.0.3 or higher is required on AIX 6.1 
AIX: Clarified that 10.2.0.4 or higher with CRS requires AIX 5.3 TL5 (5300-05) or higher – see 
Note:739371.1 
Linux x86_64: Updated 11.2 swap requirements 
Linux x86_64: Corrected WMEM_MAX setting for 10.2 
Tru64: 10.2 kernel settings clarified

012612 
Updated 11.2 RAM requirements for all 64-bit platforms (based on latest 11.2 Installation Guides) 
HP-UX: Removed references to non-existant SHMMIN kernel parameter 
HP-UX: Fixed link to 11.2 Installation Guide 
HP-UX: Added recommendation to set MAXFILES and MAXFILES_LIM to 65536 as per Note:1061351.1 
HP-UX: Added 11.2 recommendation to apply PHCO_41479 to fix an ASM disk discovery issue (unpublished Bug:10107681) 
AIX: Starting with AIX 6.1, AIXTHREAD_SCOPE=S does not need to be set – see section 5.5 (page 217) of the IBM AIX Version 6.1 Differences Guide

012712 
MAC OS X: Added OS requirements for 10.2 
AIX: Updated the recommended 11.2 kernel parameters and system configuration parameters 
Solaris: Fixed broken link to 11.2 Install Guide

022912 
Solaris: SUNWmfrun is a required package for 11.1 and 11.2 (normally installed by default) 
Linux: Required RHEL5 kernel is 2.6.18-8 or higher for 10.2 
HP-UX: Clarified that kernel parameter NFILE is replaced by MAXFILES_LIM in HP-UX 11.31 (PA-RISC and Itanium) 
Solaris: Replaced references to Sun Solaris with Oracle Solaris

030812 
Linux x86_64: unixODBC-2.2.12 and unixODBC-devel-2.2.12 recommended for 11.2 (see Note:762206.1
Linux x86_64: 11.2 SHMMAX recommendation is RAM times 0.5 (or higher at customer’s discretion – see Note:567506.1)

081412 
Solaris: Updated 11.2 swap requirements based on 11.2 Solaris Install Guide. 
Solaris: 11.2 requires SUNWhea but not SUNWmfrun 
Solaris: Added reference to Note 1190843.1 in 10.2 section 
Linux x86: 10.2 and 11.1 certified on SLES11 x86 
Linux x86-64: 11.1 certified on SLES11 x86-64, 11.2.0.3 certified on RHEL6/OEL6 x86-64

090612 
Linux: unixODBC header and library files distributed together from ftp://ftp.unixodbc.org/pub/unixODBC/ 
Solaris: SUNWxcu4 required for 11.2 RAC and 11.1 RAC 
HP-UX: Removed statement that MAXFILES_LIM directly replaces NFILE in 11.31 as this is incorrect 
HP-UX: 11.2.0.3 for HP-UX Itanium ships with JDK 1.5.0.23 which is incompatible with Itanium 2 model 9310 processors 
AIX: gpfs.base 3.2.1.8 is only required for RAC systems that will use GPFS cluster filesystems

UNIX is a trademark of the Open Group. 
AIX is a trademark of International Business Machines Corp. 
HP-UX is a trademark of Hewlett Packard Company 
Linux is a trademark of Linus Torvalds. 
Mac OS is a trademark of Apple Inc., registered in the U.S. and other countries. 
Sun, Oracle, Java and Oracle Solaris are trademarks or registered trademarks of Oracle and/or its affiliates in the United States and other countries. 
Tru64 Unix is a trademark of Compaq Information Technologies Group,. L.P. in the United States and other countries.


Comments

comments

haisins

오라클 DBA 박용석 입니다. haisins@gmail.com 으로 문의 주세요.

Oracle DB 설치 전 사전 시스템 작업 요약 정리”의 8개의 댓글

  • 2019-04-11 11:14 오후
    Permalink

    Hello there,

    My name is Aly and I would like to know if you would have any interest to have your website here at epac.to promoted as a resource on our blog alychidesign.com ?

    We are in the midst of updating our broken link resources to include current and up to date resources for our readers. Our resource links are manually approved allowing us to mark a link as a do-follow link as well
    .
    If you may be interested please in being included as a resource on our blog, please let me know.

    Thanks,
    Aly

    댓글달기
  • 2019-09-30 7:19 오후
    Permalink

    What’s Taking place i am new to this, I stumbled
    upon this I have discovered It absolutely helpful and it has helped
    me out loads. I am hoping to contribute & aid other users like its
    helped me. Good job.

    댓글달기
  • 2019-10-07 4:07 오전
    Permalink

    I’m not sure why but this website is loading very slow for me.
    Is anyone else having this issue or is it a issue on my end?
    I’ll check back later and see if the problem still exists.

    댓글달기
  • 2019-10-14 11:04 오전
    Permalink

    Would you be interested in an advertising service that costs less than $49 per month and delivers thousands of people who are ready to buy directly to your website? Please send me a reply here: jack5886tur@gmail.com to find out how this works.

    댓글달기
  • 2019-10-23 4:06 오전
    Permalink

    Hello! If you’re reading this then you’re living proof that contact form advertising works! We can send your ad message to people via their contact us form on their website. The advantage of this kind of promotion is that messages sent through contact forms are inherently whitelisted. This dramatically improves the likelihood that your advertisement will be seen. Absolutely NO Pay per click costs! Pay one flat rate and reach millions of people. To get more info send a message to: william4212sau@gmail.com

    댓글달기
  • 2019-11-17 2:29 오전
    Permalink

    Looking for effective advertising that isn’t full of crap? Sorry to bug you on your contact form but actually that was kinda the point. We can send your ad message to websites through their contact pages just like you’re getting this note right now. You can target by keyword or just start mass blasts to sites in the location of your choice. So let’s assume you want to send a message to all the web developers in the USA, we’ll grab websites for only those and post your promo to them. As long as you’re promoting some kind of offer that’s relevant to that business category then your business will get an amazing response!

    Shoot an email to eliza3644will@gmail.com to get info and prices

    댓글달기
  • 2020-01-24 3:29 오후
    Permalink

    Are you trying to find effective online marketing that actually gets good results? I apologize for sending you this message on your contact form but actually that was kinda the point. We can send your ad message to websites through their contact pages just like you’re reading this ad right now. You can specify targets by keyword or just go with mass blasts to websites in the location of your choice. So let’s say you want to push through a message to all the plumbing companies in the USA, we’ll scrape websites for only those and post your ad message to them. Providing you’re promoting something that’s relevant to that niche then you’ll receive awesome results!

    Shoot an email to alfred3545will@gmail.com to find out how we do this

    댓글달기
  • 2020-02-20 3:23 오전
    Permalink

    Are you seeking effective online marketing that doesn’t charge a fortune and gets amazing resuts? Sorry to bug you on your contact form but actually that was the whole point. We can send your ad message to websites through their contact forms just like you’re reading this note right now. You can target by keyword or just fire off bulk blasts to websites in the location of your choice. So let’s assume you’re looking to blast an ad to all the web developers in the USA, we’ll grab websites for just those and post your promo to them. Providing you’re advertising a product or service that’s relevant to that type of business then you’ll get an amazing response!

    Shoot an email to paul5268jac@gmail.com for the full details

    댓글달기

댓글 남기기

이메일은 공개되지 않습니다. 필수 입력창은 * 로 표시되어 있습니다